GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provide an overview of each diagnostic category.

DTC Descriptor

DTC P0463: Fuel Level Sensor Circuit High Voltage

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

Fuel Level Sensor Reference Voltage Circuit

P0462

--

P0461

Fuel Level Sensor Signal Circuit

P0462

P0463

P0464

P0463

P0461

Fuel Level Sensor Low Reference Circuit

--

P0463

P0464

P0463

P0461

Circuit/System Description

The fuel level sensor changes resistance in response to the fuel level. The engine control module (ECM) monitors the signal circuit of the fuel level sensor in order to determine the fuel level. When the fuel tank is full, the sensor resistance is low and the ECM senses a low signal voltage. When the fuel tank is empty, the sensor resistance is high and the ECM senses a high signal voltage. The ECM uses the signal circuit of the fuel level sensor in order to calculate the percentage of remaining fuel in the tank. The ECM sends the fuel level percentage via serial data circuit to the body control module (BCM). The BCM sends serial data messages to the instrument panel cluster (IPC) in order to control the fuel gage and display the fuel level.

Conditions for Running the DTC

    • The ignition is ON, with the engine running.
    • The system voltage is between 9-16 volts.

Conditions for Setting the DTC

    • The sensor output is greater than 2.9 volts.
    • The above condition is present for greater than 30 seconds.

Action Taken When the DTC Sets

    • The fuel gage defaults to empty.
    • The low fuel indicator illuminates.
    • The ECM records the operating conditions at the time that the diagnostic test fails. The ECM displays the failure information in the Failure Records on the scan tool.

Conditions for Clearing the DTC

    • The DTC becomes history when the conditions for setting the DTC are no longer present.
    • The history DTC clears after 40 malfunction-free warm-up cycles.

Reference Information

Schematic Reference

    •  Instrument Cluster Schematics
    •  Engine Controls Schematics for the 2.4L engine
    •  Engine Controls Schematics for the 3.5L engine
    •  Engine Controls Schematics for the 3.6L engine
    •  Engine Controls Schematics for the 3.9L engine

Connector End View Reference

    •  Displays and Gages Connector End Views
    •  Engine Control Module Connector End Views for the 2.4L engine
    •  Engine Control Module Connector End Views for the 3.5L engine
    •  Engine Control Module Connector End Views for the 3.6L engine
    •  Engine Control Module Connector End Views for the 3.9L engine

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

Scan Tool Data List

Circuit/System Verification

With the scan tool installed and the ignition ON, the Fuel Tank Level Remaining parameter in the ECM EVAP Data List indicates a value at or greater than 4 percent.

Circuit/System Testing

  1. Ignition OFF, disconnect the harness connector at the fuel level sensor.
  2. Ignition OFF, test for less than 1 ohm of resistance between the fuel level sensor low reference circuit terminal D and ground.
  3. If greater than the specified range, test the low reference circuit for a short to voltage or an open/high resistance. If the circuits tests normal, replace the ECM.
  4. Install a 3A fused jumper wire between the fuel level sensor signal circuit terminal A and the fuel level sensor low reference circuit terminal D. Verify the Fuel Tank Level Remaining parameter is greater than 98 percent.
  5. If less than 98 percent, test the fuel level sensor signal and low reference circuits for a short to voltage or an open/high resistance. If the circuits test normal, replace the ECM.
  6. If all circuits test normal, perform the fuel level sensor component test before replacing either the primary or secondary fuel level sensor.

Component Testing

  1. Ignition OFF, disconnect the harness connector at the fuel level sensor.
  2. While sweeping the fuel level sensor through its full range of motion, test for a minimum value less than 41 ohms and a maximum value greater than 119 ohms of resistance between signal terminal A and the low reference terminal D.
  3. If not within the specified range, replace the fuel level sensor.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Fuel Level Sensor Replacement for the 2.4L engine
    •  Fuel Sender Assembly Replacement for the 3.5L engine
    •  Fuel Level Sensor Replacement for the 3.6L engine
    •  Fuel Level Sensor Replacement for the 3.9L engine
    •  Control Module References for the ECM replacement, setup and programming