GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Oldsmobile 🢒 1999 🢒 Intrigue 🢒 Engine 🢒 Engine Controls - 3.8L 🢒 Fuel System Pressure Test

Object Number: 12282 Size: MF
(1)In-Line Fuel Filter
(2)Fuel Feed Pipe
(3)Fuel Pump Flex Pipe
(4)Modular Fuel Sender
(5)Fuel Return Pipe
(6)Fuel Pressure Guage
(7)Fuel Rail Assembly
(8)Fuel Pressure Regulator
(9)Fuel Pipe Shut-off Adapters

Circuit Description

When the ignition switch is turned on, the powertrain control module (PCM) turns on the in-tank fuel pump. The in-tank fuel pump remains on as long as the engine is cranking or running and the PCM is receiving reference pulses. If there are no reference pulses, the PCM turns the in-tank fuel pump off 2 seconds after the ignition switch is turned on, or 2 seconds after the engine stops running. The in-tank fuel pump is an electric pump within an integral reservoir. The in-tank fuel pump supplies fuel through the fuel feed pipe, and in-line fuel filter to the fuel rail assembly. The fuel pump is designed to provide fuel at a pressure above the pressure needed by the fuel injectors. A fuel pressure regulator attached to the fuel rail keeps the fuel available to the fuel injectors at a regulated pressure. Unused fuel is returned to the fuel tank by a separate fuel return pipe. The J 34730-1A fuel pressure gauge and the J 37287 fuel pipe shut off adapters are used for fuel system diagnosis.

Test Description

The number(s) below refer to the step number(s) on the Diagnostic Table.

  1. To relieve the fuel pressure, refer to Fuel Pressure Relief . With the ignition switch on and the fuel pump running, the fuel pressure indicated by the fuel pressure gage should be 333-376 kPa (48-55 psi). This pressure is controlled by the amount of pressure the spring inside the fuel pressure regulator can provide.

  2. A fuel system that drops more than 5 psi in 10 minutes has a leak in one or more of the following areas:

    3. • The fuel pump check valve.
    • The fuel pump flex pipe.
    • The valve or valve seat within the fuel pressure regulator.
    • The fuel injector(s).

  3. Fuel pressure that drops-off during acceleration, cruise or hard cornering may cause a lean condition. A lean condition can cause a loss of power, surging, or misfire. A lean condition can be diagnosed using a scan tool. If an extremely lean condition occurs, the oxygen sensors stop toggling. The oxygen sensor output voltages drop below 500 mV. Also, the fuel injector width increases.

Important: Make sure the fuel system is not operating in the Fuel Cut-Off mode. This may cause false indications by the scan tool. Refer to Engine Scan Tool Data List

  1. When the engine is at idle, the manifold pressure is low (high vacuum). This low pressure (high vacuum) is applied to the fuel pressure regulator diaphragm. The low pressure (high vacuum) offsets the pressure being applied to the fuel pressure regulator diaphragm by the spring inside the fuel pressure regulator. When this happens, the result is lower fuel pressure. The fuel pressure at idle varies slightly as the barometric pressure changes, but the fuel pressure at idle should always be less than the fuel pressure noted in Step 2 with the engine off.

    2.

  2. A rich condition may result from the fuel pressure being above 376 kPa (55 psi). A rich condition may cause a DTC P0132 or a DTC P0172 to set. Driveability conditions associated with rich conditions may include hard starting (followed by black smoke) and a strong sulfur smell in the exhaust.

    3.

  3. This test determines if the high fuel pressure is due to a restricted fuel return pipe or if the high fuel pressure is due to a faulty fuel pressure regulator.

    4.

  4. A lean condition may result from the fuel pressure being below 333 kPa (48 psi). A lean condition may cause a DTC P0131 or a DTC P0171 to set. Driveability conditions associated with lean conditions may include hard starting (when the engine is cold), hesitation, poor driveability, lack of power, surging, and misfiring.

    5.

  5. Restricting the fuel return pipe with the fuel pipe shut-off adapter Refer toJ 37287 causes the fuel pressure to rise above the regulated fuel pressure. Using a scan tool to pressurize the system, the fuel pressure should rise above 376 kPa (55 psi) as the valve on the fuel pipe shut-off adapter connected to the fuel return pipe becomes partially closed.

    Notice: Do not allow the fuel pressure to exceed 450 kPa (65 psi). Fuel pressure in excess of 450 kPa (65 psi) may damage the Fuel Pressure Regulator.

  6. Check the spark plug associated with a particular fuel injector for fouling or saturation in order to determine if that particular fuel injector is leaking. If checking the spark plug associated with a particular fuel injector for fouling or saturation does not determine that a particular fuel injector is leaking, use the following procedure.

    7. 1. Remove the fuel rail, but leave the fuel pipes connected to the fuel rail. Refer to Fuel Injection Fuel Rail Assembly Replacement .
    2. Lift the fuel rail just enough to leave the fuel injector nozzles in the fuel injector ports.

    Caution: In order to reduce the risk of fire and personal injury that may result from fuel spraying on the engine, verify that the fuel rail is positioned over the fuel injector ports. Also verify that the fuel injector retaining clips are intact.

    3. Pressurize the fuel system using a scan tool.
    4. Visually and physically inspect the fuel injector nozzles for leaks.

Step

Action

Value(s)

Yes

No

1

Did you perform the Powertrain On-Board Diagnostic (OBD) System Check?

--

Go to Step 2

Go to Powertrain On Board Diagnostic (OBD) System Check

2

  1. Turn the ignition off.
  2. Turn the air conditioning system off.

    3. Caution: Wrap a shop towel around the fuel pressure connection in order to reduce the risk of fire and personal injury. The towel will absorb any fuel leakage that occurs during the connection of the fuel pressure gage. Place the towel in an approved container when the connection of the fuel pressure gage is complete.

  3. Install a J 34730-1A fuel pressure gauge.
  4. Place the bleed hose of the fuel pressure gauge into an approved gasoline container.
  5. Turn the ignition on.
  6. Bleed the air out of the fuel pressure gauge into an approved gasoline container.
  7. Turn the ignition off for 10 seconds.
  8. Turn the ignition on.

    9. Important:: The fuel pump will run for approximately 2 seconds. Cycle the ignition as necessary in order to achieve the highest possible fuel level

  9. Observe the fuel pressure indicated by the fuel pressure gage with the fuel pump running.

Is the fuel pressure within the specified range?

333-376 kPa (48-55 psi)

Go to Step 3

Go to Step 12

3

Important: The fuel pressure may vary slightly when the fuel pump stops running. The fuel pressure should stabilize and remain constant.

Note the fuel pressure after the fuel pump stops running.

Does the fuel pressure drop more than the specified value in 10 minutes?

34 kPa (5 psi)

Go to Step 10

Go to Step 4

4

Relieve the fuel pressure to the specified value.

Does the fuel pressure drop more than the specified value in 10 minutes?

69 kPa (10 psi)

14 kPa (2 psi)

Go to Step  19

Go to Step 5

5

Is the fuel pressure suspected of dropping-off during acceleration, cruise, or hard cornering.

--

Go to Step 6

Go to Step 8

6

Visually and physically inspect the following items for a restriction:

    • The in-line fuel filter.
    • The fuel feed pipe.

Was a restriction found?

--

Go to Step  24

Go to Step 7

7
  1. Remove the modular sender assembly. Refer to Fuel Sender Assembly Replacement
  2. Visually and physically inspect the following items:
    3. • The fuel pump strainer for a restriction.
    • The fuel pump strainer for correct position, and installation on the fuel sender assembly
    • The fuel pump flex pipe for leaks.
    • Verify the fuel pump is the correct fuel pump for this vehicle.

Was a problem found in any of these areas?

--

Go to Step 24

Go to Step  19

8

  1. Turn the ignition off for 10 seconds.
  2. Turn the ignition on.

    3. Important:: The fuel pump will run for approximately 2 seconds. Cycle the ignition as necessary in order to achieve the highest possible fuel level. Note this pressure.

  3. Start the engine.
  4. Allow the engine to idle at normal operating temperature.

Is the fuel pressure less than the noted fuel pressure by the amount specified?

21-69 kPa (3-10 psi)

Go to Symptoms

Go to Step  9

9
  1. Disconnect the vacuum hose from the fuel pressure regulator.
  2. With the engine idling, apply 12-14 inches of vacuum to the fuel pressure regulator.

Does the fuel pressure drop by the amount specified?

21-69 kPa (3-10 psi)

Go to Step 20

Go to Step 21

10
  1. Relieve the fuel pressure. Refer to Fuel Pressure Relief .
  2. Disconnect the fuel feed pipe and the fuel return pipe from the fuel rail. Refer to Metal Collar Quick Connect Fitting Service .
  3. Install the J 37287 fuel pipe shut-off adapters between the fuel feed pipe and the fuel return pipe and the fuel rail.

    4. Notice: Do not allow the fuel pressure to exceed 450 kPa (65 psi). Fuel pressure in excess of 450 kPa (65 psi) may damage the Fuel Pressure Regulator.

  4. Open the valves on the fuel pipe shut-off adapters.
  5. Turn the Ignition off.

  6. Use a scan tool in order to pressurize the fuel system.

  7. Place the bleed hose of the fuel pressure gauge into an approved gasoline container.
  8. Bleed the air out of the fuel pressure gauge.
  9. Wait for the fuel pressure to build.
  10. Close the valve in the fuel pipe shut-off adapter that is connected to the fuel feed pipe.

Does the fuel pressure remain constant?

--

Go to Step 19

Go to Step  11

11
  1. Open the valve in the fuel pipe shut-off adapter that is connected to the fuel feed pipe.
  2. Use the scan tool in order to pressurize the fuel system.
  3. Wait for the fuel pressure to build.
  4. Close the valve in the fuel pipe shut-off adapter that is connected to the fuel return pipe.

Does the fuel pressure remain constant?

--

Go to Step 21

Go to Step  22

12

Is the fuel pressure above the specified value?

376 kPa (55 psi)

Go to Step 13

Go to Step 15

13

  1. Relieve the fuel pressure. Refer to Fuel Pressure Relief .
  2. Disconnect the fuel return pipe from the fuel rail. Refer to Metal Collar Quick Connect Fitting Service .
  3. Attach a length of flexible fuel hose to the fuel rail return outlet passage
  4. Place the open end of the flexible hose into an approved gasoline container.
  5. Turn the ignition off for approximately 10 seconds.
  6. Turn the ignition on.
  7. Observe the fuel pressure gauge with the fuel pump running.

Is the fuel pressure within the specified range?

333-376 kPa (48-55 psi)

Go to Step 23

Go to Step 14

14

Visually and physically inspect the fuel rail outlet passages for a restriction.

Was a restriction found?

--

Go to Step  24

Go to Step 21

15

Is the fuel pressure above the specified value?

0 kPa (0 psi)

Go to Step 16

Go to Step  17

16

  1. Relieve the fuel pressure. Refer to Fuel Pressure Relief .
  2. Disconnect the fuel return pipe from the fuel rail. Refer to Metal Collar Quick Connect Fitting Service .
  3. Install the J 37287 fuel pipe shut-off adapter between the fuel return pipe and the fuel rail.
  4. Open the valve on the fuel pipe shut-off adapter.
  5. Turn the ignition off.
  6. Use the scan tool in order to pressurize the fuel system.

    7. Notice: Do not allow the fuel pressure to exceed 450 kPa (65 psi). Fuel pressure in excess of 450 kPa (65 psi) may damage the Fuel Pressure Regulator.

  7. Place the bleed hose of the fuel pressure gauge into an approved gasoline container.
  8. Bleed the air out of the fuel pressure gauge.
  9. Slowly close the valve in the fuel pipe shut-off adapter that is connected to the fuel return pipe.

Does the fuel pressure exceed the specified range?

333-376 kPa (48-55 psi)

Go to Step 21

Go to Step 7

17

Perform the Fuel System Electrical Test. Refer to Fuel Pump Electrical Circuit Diagnosis .

Was a problem found with the fuel pump electrical circuit?

--

Go to Step 24

Go to Step 18

18

Visually and physically inspect the following items:

    • The in-line fuel filter for obstructions.
    • The fuel feed pipe for a restriction.
    • The fuel pump strainer for obstructions.
    • The fuel pump flex pipe for leaks.

Important: It will be necessary to remove the fuel sender assembly in order to inspect the fuel pump strainer and the fuel pump flex pipe. Refer to Fuel Sender Assembly Replacement .

Was a problem found in any of these areas?

--

Go to Step 24

Go to Step  19

19

Replace the modular fuel sender assembly.

Did you complete the repair?

--

Go to Step  25

--

20

Locate and repair the loss of vacuum to the fuel pressure regulator.

Did you complete the repair?

--

Go to Step  25

--

21

Replace the fuel pressure regulator.

Did you complete the repair?

--

Go to Step  25

--

22

Locate and replace any leaking fuel injectors.

Did you complete the repair?

--

Go to Step  25

--

23

Locate and correct the restriction in the fuel return pipe.

Did you complete the repair?

--

Go to Step  25

--

24

Repair the problem as necessary.

Did you complete the repair?

--

Go to Step  25

--

25
  1. Turn the ignition off.
  2. Turn the air conditioning system off.

    3. Caution: Wrap a shop towel around the fuel pressure connection in order to reduce the risk of fire and personal injury. The towel will absorb any fuel leakage that occurs during the connection of the fuel pressure gage. Place the towel in an approved container when the connection of the fuel pressure gage is complete.

  3. Install the J 34730-1A fuel pressure gauge.
  4. Place the bleed hose of the fuel pressure gauge into an approved gasoline container.
  5. Turn the ignition on.
  6. Bleed the air out of the fuel pressure gauge into an approved gasoline container.
  7. Turn the ignition off for 10 seconds.
  8. Turn the ignition on.

    9. Important:: The fuel pump will run for approximately 2 seconds. Cycle the ignition as necessary in order to achieve the highest possible fuel level

  9. Observe the fuel pressure indicated by the fuel pressure gage with the fuel pump running.

Is the fuel pressure within the specified range?

333-376 kPa (48-55 psi)

Go to Step26

Go to Step11

26

Important: The fuel pressure may vary slightly when the fuel pump stops running. The fuel pressure should stabilize and remain constant.

Note the fuel pressure after the fuel pump stops running.

Does the fuel pressure drop more than the specified value in 10 minutes?

34 kPa (5 psi)

Go to Step10

System OK