Schematic Reference: Starting and Charging Schematics

Did you preform the Battery Inspection/Test?

Go to Step 2

Go to Battery Inspection/Test

Turn the ignition switch to the START position.

Does the engine crank?

Go to Testing for Intermittent Conditions and Poor Connections

Go to Step 3

Turn the ignition switch to the START position.

Does the starter motor relay click?

Go to Step 7

Go to Step 4

1. Remove the starter motor relay.
2. Connect a test light from the supply voltage circuit of the starter motor relay coil circuit to ground.
3. With the transmission in park or clutch pedal depressed, turn the ignition switch to the START position.

Does the test light illuminate?

Go to Step 5

Go to Step 6

1. Connect a test light from the supply voltage circuit of the starter motor relay coil circuit to the control circuit of the starter motor relay coil circuit.
2. With the transmission in park or clutch pedal depressed, turn the ignition switch to the START position.

Does the test light illuminate?

Go to Step 13

Go to Step 10

1. Turn OFF the ignition.
2. Disconnect the park neutral position (PNP) switch, refer to Park/Neutral Position and Backup Lamp Switch Replacement or the clutch start switch, or Clutch Pedal Position Switch Replacement .
3. Turn ON the ignition, with the engine OFF.
4. Connect a 10-amp fused jumper between the starter motor relay coil control circuits of the PNP switch or clutch pedal position switch.
5. With the transmission in park or clutch pedal depressed, turn the ignition switch to the START position.

Does the test lamp illuminate?

Go to Step 14

Go to Step 11

1. Turn OFF the ignition.
2. Remove the starter motor relay.
3. Connect a test lamp between the battery positive voltage circuit of the starter motor relay switch circuit and a good ground.

Does the test lamp illuminate?

Go to Step 8

Go to Step 17

Connect a 30-amp fused jumper between the battery positive voltage circuit of the starter motor relay switch circuit and the supply voltage circuit of the starter solenoid.

Does the engine crank?

Go to Step 13

Go to Step 9

Does the fuse in the jumper open?

Go to Step 18

Go to Step 12

Test the control circuit of the starter motor relay for an open or high resistance. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

Go to Step 23

Go to Step 19

Test the supply voltage circuit of the starter motor relay coil circuit for an open or high resistance. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

Go to Step 23

Go to Step 15

Test the supply voltage circuit of the starter solenoid for an open or high resistance. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

Go to Step 23

Go to Step 16

Inspect for poor connections at the starter motor relay. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

Go to Step 23

Go to Step 19

1. If equipped with an automatic transmission, inspect for poor connection at the PNP switch harness connector. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . If OK, perform the Park/Neutral Position and Backup Lamp Switch Adjustment .
2. If equipped with a manual transmission, inspect for poor connection at the Clutch/Starter Interlock Switch harness connector. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

Go to Step 23

Go to Step 20

Inspect for poor connections at the ignition switch harness connector. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

Go to Step 23

Go to Step 21

Inspect for poor connections at the starter solenoid. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

Go to Step 23

Go to Step 22

Repair the open or high resistance in the battery positive voltage circuit of the starter motor relay switch circuit. Refer to Wiring Repairs .

Did you complete the repair?

Go to Step 23

--

Repair the short to ground in the supply voltage circuit of the starter solenoid. Refer to Wiring Repairs .

Did you complete the repair?

Go to Step 23

--

Replace the Starter Relay. Refer to Relay Replacement .

Did you complete the replacement?

Go to Step 23

--

1. Replace the PNP switch. Refer to Park/Neutral Position and Backup Lamp Switch Replacement .
2. Replace the clutch start switch. Refer to Clutch Pedal Position Switch Replacement .

Did you complete the replacement?

Go to Step 23

--

Replace the ignition switch. Refer to Ignition and Start Switch Replacement .

Did you complete the replacement?

Go to Step 23

--

Replace the starter. Refer to Starter Motor Replacement .

Did you complete the replacement?

Go to Step 23

--

Operate the system for which the symptom occurred.

Did you correct the condition?

System OK

Go to Step 2