Removal Procedure
- Open the sunshade to the full open position.
- Remove the sunroof front trim cover. Refer to Sunroof Front Trim Cover Replacement .
- Remove the sunroof motor. Refer to Power Sunroof Motor Replacement .
- Remove the screws from around the lower frame.
- Remove the sunroof module and window from the vehicle.
- Remove the sunroof motor. Refer to Power Sunroof Motor Replacement .
- Remove the cam plate screws (1).
- Remove the cam plate (2).
- Lift upward on the drive cables (2) to release the cam (3) from the upper frame.
- Remove the left and right side drive cable tube covers (1) from the drive cable (2).
- Push the drive cables up into the upper frame, this will allow the window to open manually.
- The sunroof window must be in the full open position to do the following:
- Remove the two screws (1) on each side of the guides (2).
- Rotate the upper frame back and fourth. Pushing forward on the upper frame until it is over the guides.
- Remove the upper frame (2) from the window and guides (1).
- Remove the guides (1) from the drive cables (4) and slides (3).
Important: Note the location of the bolts, size and color when removing, for proper installation.
Important: Place the sunroof module on a flat protective cover, face down.
Two drive cable tube covers to each side.
Important: Place the sunroof module on a flat protective cover, face down.
| 12.1. | Unhook the wind deflector slide blocks (1) from each side. |
| 12.2. | Unhook the wind deflector tabs (2) from the center of the upper frame. |
| 12.3. | Remove the wind deflector. |
Important : Mark the left and right sides of the guides in respect to the frame. This will assist in the alignment of the window to the module later.
Note the location of the bolts, size and color when removing, for proper installation.
Important : Place the sunroof module on a flat protective cover, face down. It is necessary to slide the guides about 1 cm (1 3/8 in) rearward to release the upper frame.
Installation Procedure
- Install the guides (1) to the drive cables (4) and slides (3).
- Install the upper frame (2) to the window and guides (1).
- Place the guides about 1 cm (1 3/8 in) rearward to reinstall the upper frame.
- Pull rearward on the upper frame until the screws holes align with the guide holes.
- Install the two screws (1) to each side of the guides (2).
- The sunroof window must be in the full open position to do the following:
- Install the left and right side drive cable tube covers (1) to the cable (2).
- Pull the drive cables down through the guides and around the upper frame, this will allow the window to be closed manually.
- Install the drive cables (2) with cam (3).
- Install the cam plate (2).
- Install the cam plate screws (1).
- Install the sunroof module to the vehicle.
- Install the lower frame to the sunroof module.
- Tighten the lower frame to the sunroof module screws.
- Install the sunroof motor. Refer to Power Sunroof Motor Replacement .
- Install the sunroof front trim cover. Refer to Sunroof Front Trim Cover Replacement .
- Verify the operations of the sunroof window.
Important: Place the sunroof module on a flat protective cover, face down. Rotate the upper frame back and fourth until it is over the guides. Refer to the marked positions on the guides in respect to the frame.
Notice: Refer to Fastener Notice in the Preface section.
Important : Using the marks on the left and right sides of the guides to reinstall the window to the module for alignment.
Install the bolts, size and color to the proper location.
Tighten
Tighten the screw to 3 N·m (27 lb in).
Important: Place the sunroof module on a flat protective cover, face down.
| 6.1. | Install the wind deflector. |
| 6.2. | Hook the wind deflector slide blocks (1) to each side. |
| 6.3. | Hook the wind deflector tabs (2) to the center of the upper frame. |
Two drive cable tube covers to each side.
Ensure that the chamfered edge of the gear is directed upward.
Tighten
Tighten the screw to 3 N·m (27 lb in).
Tighten
Tighten the screw to 3 N·m (27 lb in).
