Circuit Description
The body control module (BCM) applies a ground through the brake pedal position sensor reference low circuit to the brake pedal position sensor. The BCM supplies a 10-volt reference through the brake sensor reference voltage circuit to the brake pedal position sensor. The brake pedal position sensor sends a variable voltage signal through the brake pedal position sensor signal circuit to the BCM as the brake pedal is applied.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC C0277 Brake Pedal Position Sensor Circuit
Conditions for Running the DTC
The battery voltage must be between 9-16 volts.
Conditions for Setting the DTC
| • | A short to ground or a short to voltage in the brake pedal position sensor signal circuit is present. |
| • | A short to voltage, a short to ground, or an open in the 10-volt reference circuit of the brake pedal position sensor |
| • | An open in the low reference circuit of the brake pedal position sensor |
| • | A malfunctioning brake pedal position sensor |
Action Taken When the DTC Sets
The stop lamps may not function correctly.
Conditions for Clearing the DTC
| • | The DTC will clear on current status after the condition for setting the fault is corrected. |
| • | A history DTC will clear after 100 consecutive ignition cycles without a fault present. |
| • | History and current DTC can be cleared using a scan tool. |
Diagnostic Aids
Perform a visual inspection for loose or poor connections at all related components. Refer to Testing for Intermittent Conditions and Poor Connections .
Step | Action | Yes | No | ||||||
|---|---|---|---|---|---|---|---|---|---|
Schematic Reference: Exterior Lights Schematics Connector End View Reference: Master Electrical Component List | |||||||||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | |||||||
2 |
Do the stop lamps operate as expected? | Go to Testing for Intermittent Conditions and Poor Connections | Go to Step 3 | ||||||
3 | Test the brake pedal position sensor signal circuit for high resistance or an short to voltage. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | Go to Step 12 | Go to Step 4 | ||||||
4 | Test the brake pedal position sensor low reference circuit for a high resistance or an open. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | Go to Step 12 | Go to Step 5 | ||||||
5 | Test the 10-volt reference circuit for the following:
Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | Go to Step 12 | Go to Step 6 | ||||||
6 | Test the instrument panel (I/P) dimming voltage reference circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | Go to Step 12 | Go to Step 7 | ||||||
7 | Inspect for poor connections at the harness connector of the brake pedal position sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | Go to Step 12 | Go to Step 8 | ||||||
8 |
Important: Always recalibrate the brake pedal position sensor after replacing the brake position sensor. Refer to Brake Pedal Position Sensor Calibration . Replace the brake pedal position sensor. Refer to Brake Pedal Position Sensor Replacement . Did you complete the replacement? | Go to Step 9 | -- | ||||||
9 |
Does DTC C0277 reset? | Go to Step 10 | Go to Step 12 | ||||||
10 | Inspect for poor connections at the harness connector of the body control module (BCM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | Go to Step 12 | Go to Step 11 | ||||||
11 | Replace the BCM. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement? | Go to Step 12 | -- | ||||||
12 |
Does the DTC reset? | Go to Step 2 | System OK | ||||||
