Diagnostic Instructions
DTC Descriptors
DTC P0012: Intake Camshaft Position (CMP) System Performance - Retarded
DTC P0015: Exhaust Camshaft Position (CMP) System Performance - Retarded
Diagnostic Fault Information
Circuit
| Short to Ground
| High Resistance
| Open
| Short to Voltage
| Signal Performance
|
Intake/Exhaust CMP Solenoid High Control
| P0010/P0013
| P0012/P0015
| P0010/P0013
| P0010/P0013
| --
|
Intake/Exhaust CMP Solenoid Low Control
| P0010, P0011/P0013, P0015
| P0012/P0015
| P0010/P0013
| --
| --
|
Circuit/System Description
The CMP actuator solenoid enables the powertrain control module (PCM) to change the intake and exhaust camshaft timing while the engine is running. The CMP actuator solenoid contains a spool valve that controls the advance of the camshaft. The CMP actuator
solenoid valve is controlled by a pulse width modulated (PWM) signal from the PCM. The CMP sensor monitors the camshaft position or the camshaft angle, and compares that position or phase to the crankshaft position (CKP) sensor signal. The PCM determines whether
the camshaft angle is correct by comparing the actual camshaft position to the target camshaft position. By continuously analyzing the input of the CMP sensor and the CKP sensor the PCM can detect a fault in the CMP actuator system.
Conditions for Running the DTC
| • | DTCs P0100, P0101, P0102, P0103, P0115, P0116, P0117, P0118, P0125, P0335, P0339, P0340, P0342, P0343, P0351, P0352, P0353, P0354, P0365, P0367, P0368 are not set. |
| • | Battery voltage is greater than 11 volts. |
| • | The engine is running between 500-4,000 RPM. |
| • | The engine coolant temperature (ECT) is between 75-100°C (167-212°F). |
| • | The vehicle is driven at greater than 64 km/h (40 mph) for greater than 3 minutes. |
| • | DTC P0012 and P0015 run once per drive cycle when the above conditions are met. |
Conditions for Setting the DTC
| • | The PCM does not detect a change in the camshaft timing. |
| • | The PCM detects that the camshaft timing is fixed. |
| • | Either of the above conditions occurs twice when the CMP actuator solenoid is activated. |
Action Taken When the DTC Sets
| • | DTC P0012 is a type B DTC. |
| • | DTC P0015 is a type A DTC. |
Conditions for Clearing the DTC
| • | DTC P0012 is a type B DTC. |
| • | DTC P0015 is a type A DTC. |
Diagnostic Aids
| • | Inspect for any recent engine mechanical repairs. An incorrectly timed or incorrectly installed camshaft can cause a DTC P0012 or P0015 to set. |
| • | Inspect the CMP sensor reluctor for a damaged tooth. A damaged reluctor can cause an incorrect CMP sensor reading that may set a false DTC P0012 or P0015. |
| • | If a DTC P0012 and P0010 are both present, test for a condition in the intake CMP actuator solenoid control circuits. |
| • | If a DTC P0015 and P0013 are both present, test for a condition in the exhaust CMP actuator solenoid control circuits. |
| • | Electrical resistance in the CMP actuator solenoid control circuits can affect solenoid spool valve movement and cause a DTC P0012 or P0015 to set. |
| • | An intermittent DTC P0012 or P0015 can be caused by a loss in the oil supply to the CMP solenoid valve or the CMP actuator assembly. |
Reference Information
Schematic Reference
Engine Controls Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
Camshaft Actuator System Description
Electrical Information Reference
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
Important: All CMP actuator system DTCs must be cleared before the CMP actuator solenoid scan tool output control is enabled.
- Engine running at normal operating temperature, command the applicable CMP actuator solenoid ON with the scan tool. The engine should run rough or stall.
- Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
- Ignition OFF, disconnect the harness connector at the camshaft position (CMP) actuator solenoid.
- Ignition OFF, test for less than 10 ohms between the CMP low control circuit terminal 2 and ground G104.
| ⇒ | If greater than the specified range, test the CMP low control circuit for an open/high resistance. If the circuit tests normal, replace the PCM. |
- Disconnect the PCM harness connector X2 at the PCM.
- Ignition ON, test for infinite resistance between the CMP low control circuit terminal 2 and ground G104.
| ⇒ | If less than the specified range, repair the short to ground in the CMP low control circuit. |
- Engine running, connect the CMP actuator solenoid to B+ and ground with a pair of 10A fused jumper wires. Verify the engine runs rough or stalls.
| ⇒ | If the engine does not run rough or stall, remove the CMP actuator solenoid and verify the solenoid plunger moves 3 mm (0.125 in) when connected to B+ and ground. If the solenoid plunger moves less than the specified range, test or
replace the CMP actuator solenoid. If the solenoid plunger moves greater than the specified range, test the following conditions: |
| • | A plugged or restricted CMP actuator solenoid oil filter |
| • | A blockage or restriction in the CMP actuator system oil passages |
- Test the solenoid high control circuit terminal 1 for high resistance. If the circuit tests normal, replace the PCM.
- If all circuits test normal, test or replace the CMP actuator solenoid.
Component Testing
- Ignition OFF, disconnect the harness connector at the CMP actuator solenoid.
- Test for 6.9-7.9 ohms at 20°C (68°F) between the actuator solenoid terminals 1 and 2
| ⇒ | If not within the specified range, replace the CMP actuator solenoid. |
- Test for infinite resistance between each terminal and the solenoid housing.
| ⇒ | If not the specified value, replace the CMP actuator solenoid valve. |
Repair Instructions
Perform the
Diagnostic Repair Verification after completing the diagnostic procedure.
