GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

Symptoms Description

Symptoms covers conditions that are not detected by DTCs. Certain conditions can cause multiple symptoms. These conditions are listed together under Symptoms Testing. Conditions that may only cause specific symptoms are listed separately under Additional Symptoms Testing. Perform the Symptoms Testing before using the Additional Symptoms Testing.

Symptoms Definition

Backfire:  Fuel ignites in the intake manifold or in the exhaust system, making a loud popping noise.

Cuts Out, Misses: A steady pulsation or jerking that follows engine speed, which is usually more pronounced as the engine load increases. This condition is not normally felt above 1,500 RPM or 48 km/h (30 mph). The exhaust has a steady spitting sound at idle or at low speed.

Detonation/Spark Knock: A mild to severe ping which usually occurs worse while under acceleration. The engine makes sharp metallic knocks that change with throttle opening.

Dieseling, Run-On:  Fuel ignites in the intake manifold or in the exhaust system, making a loud popping noise.

Hard Start: Engine cranks OK, but does not start for a long time. The vehicle does eventually run, or may start but immediately stalls.

Hesitation, Sag, Stumble: Momentary lack of response as the accelerator is pushed down. This condition can occur at any vehicle speed. This condition is usually more pronounced when first trying to make the vehicle move, as from a stop. This condition may cause the engine to stall in severe conditions.

Lack of Power, Sluggishness, or Sponginess: The engine delivers less than expected power. Little or no increase in speed when the accelerator pedal is pushed down part way.

Poor Fuel Economy:  Fuel economy, as measured by an actual road test, is noticeably lower than expected. Also, the fuel economy is noticeably lower than it was on this vehicle at one time, as previously shown by an actual road test.

Poor Fuel Fill Quality:  Difficulty when refueling the vehicle.

Rough, Unstable, or Incorrect Idle and Stalling: The engine runs unevenly at idle. If severe, the engine or the vehicle may shake. Engine idle may vary in speed. Either condition may be severe enough to stall the engine.

Surges/Chuggles: Engine power variation under steady throttle or cruise. Feels like the vehicle speeds up and slows down with no change in the accelerator pedal position.

Symptoms Verification

Verify all of the following conditions are true:

    • The powertrain control module (PCM) and the malfunction indicator lamp (MIL) are operating correctly.
    • There are no diagnostic trouble codes (DTCs) stored.
    • The scan tool data is within the normal operating range.
    • Bulletins are not available for the current symptom.
    • The PCM grounds are clean, tight, and in the correct locations.
    • The vehicle tires are correctly inflated and meet original equipment specifications.
    • The air filter element is not restricted. Refer to Air Cleaner Element Replacement.

Symptoms Testing

Backfire, Cuts Out/Misses, Detonation/Spark Knock, Dieseling/Run-On, Hard Start, Hesitation/Sag/Stumble, Lack of Power/Sluggishness/Sponginess, Poor Fuel Economy, Rough, Unstable, or Incorrect Idle and Stalling, or Surges/Chuggles

  1. Test for the following conditions:
  2. • The fuel system for the following:
       - Correct fuel pressure--Refer to Fuel System Diagnosis.
       - Fuel injectors that are leaking or improper operation--Refer to Fuel Injector Solenoid Coil Test - Engine Coolant Temperature Between 10-35 Degrees C (50-95 Degrees F).
       - Contaminated or a poor fuel quality condition--Refer to Alcohol/Contaminants-in-Fuel Diagnosis. Fuel that has deteriorated because of excessive storage time, or has inferior quality or octane rating can cause numerous driveability conditions.
    • The ignition system for the following:
       - Spark plugs for incorrect heat range or an abnormal condition--Refer to Spark Plug Inspection.
       - For diagnosis of coolant or oil fouled spark plugs, refer to Base Engine Misfire with Coolant Consumption or Base Engine Misfire with Excessive Oil Consumption.
       - Wet down the secondary ignition system with water from a spray bottle--Wetting down the secondary ignition system may help locate damaged or deteriorated components. Look/listen for arcing or misfiring as the water is applied.
       - Weak spark using the J 26792 Spark Tester--Refer to Electronic Ignition (EI) System Diagnosis.
    • The operation of the automatic transmission. The incorrect engagement/disengagement of the torque converter clutch (TCC), the incorrect upshift/downshift of transmission speeds, excessive internal slipping, all can cause driveability conditions. Refer to Symptoms - Automatic Transmission.
    • The operation of the manual transmission clutch. The incorrect engagement/disengagement of clutch and incorrect clutch adjustment can cause driveability conditions. Refer to Symptoms - Manual Transmission.
    • The operation of the A/C compressor
    • Items that can cause an engine to run lean or rich--Refer to DTC P0171 or P0172.
    • The engine for the following mechanical failures--Refer to Symptoms - Engine Mechanical :
       - Excessive oil in the combustion chamber or leaking valve seals
       - Incorrect cylinder compression
       - Sticking or leaking valves
       - Worn camshaft lobes
       - Incorrect valve timing
       - Worn rocker arms
       - Broken valve springs
       - Excessive carbon buildup in the combustion chambers--Clean the chambers with top engine cleaner. Follow the product manufacturer's instructions.
       - Incorrect engine parts
    • Vacuum hoses for splits or kinks--Verify that the routing and connections are as shown on the Vehicle Emission Control Information label. Refer to Evaporative Emissions Hose Routing Diagram.
    • The correct operation of the knock sensor (KS) system. Excessive spark retard activity can cause a loss of power, poor fuel economy, and other driveability conditions. No KS requested spark retard can cause detonation. Refer to DTC P0325, P0326, P0327, or P0328 and Knock Sensor (KS) System Description.
    • The exhaust system components for the following:
       - Physical damage or possible internal failure
       - The three-way catalytic converters for a restriction--Refer to Restricted Exhaust.
       - For additional information, refer to Symptoms - Engine Exhaust.
    • Electromagnetic interference (EMI) on the reference circuit can cause a misfire condition. You can usually detect EMI with a scan tool by monitoring the engine speed parameter. A sudden increase in the engine speed parameter with little change in actual engine speed indicates that EMI is present. Inspect the high voltage components near the ignition control circuit if a condition exists.
    • Inspect the positive crankcase ventilation (PCV) system and all connections for leaks or restrictions--Refer to Crankcase Ventilation System Inspection/Diagnosis.
    • Correct operation of the evaporative emission (EVAP) system--Refer to Evaporative Emission Control System Diagnosis.
    • The engine cooling system for the following conditions:
       - The thermostat is the correct heat range--Refer to Thermostat Diagnosis.
       - Proper engine coolant level--Refer to Cooling System Draining and Filling.
    • A camshaft position (CMP) actuator that is stuck in the advanced position--Refer to DTC P0011 or P0014 and Camshaft Actuator System Description.
  3. If the above conditions do not address the symptom, refer to the additional symptoms tests.

Additional Symptoms Tests

Detonation/Spark Knock

Test the engine for an overheating condition. Refer to Symptoms - Engine Cooling.

Rough, Unstable, or Incorrect Idle and Stalling

    • Inspect the engine mounts. Refer to Engine Mount Inspection.
    • Test for excessive coking or deposits on the throttle valve and throttle bore.
    • Use the scan tool to perform a cylinder balance test by commanding individual fuel injectors OFF with the engine running--Refer to Powertrain Control Module Scan Tool Information.
    • Use the scan tool to verify the PCM is receiving idle-up inputs from the power steering high pressure switch, the A/C compressor relay, and the rear defogger relay--Refer to Powertrain Control Module Scan Tool Information.

Surges/Chuggles

Test the heated oxygen sensors (HO2S). The HO2S should respond quickly to a change in throttle position. If the HO2S do not respond to different throttle positions, inspect for contamination from fuel, silicon, or the incorrect use of RTV sealant. The sensors may have a white powdery coating and result in a high, but false, signal voltage, which gives a rich exhaust indication. The PCM reduces the amount of fuel delivered to the engine, causing a driveability condition.

Hard Start

    • Test the engine coolant temperature (ECT) sensor. Compare the ECT sensor value to the intake air temperature (IAT) sensor value on a cold engine. The ECT and IAT sensor values should be within ± 3°C (5°F). If the ECT sensor is out of range with the IAT sensor, test the resistance of the ECT sensor. Refer to Altitude Versus Barometric Pressure for resistance specifications. Replace the ECT sensor if the resistance is not within specification. Refer to Engine Coolant Temperature Sensor Replacement. If the sensor is within the specification, test the ECT circuits for a high resistance.
    • Test the fuel pump relay operation. The fuel pump should turn ON for 2 seconds when the ignition is turned ON. Refer to Fuel Pump Electrical Circuit Diagnosis.

Hesitation, Sag, Stumble

Verify the generator output voltage is within 9-16 volts. Refer to Symptoms - Engine Electrical.

Poor Fuel Economy

Review the owner's driving habits for any of the following:

    • The A/C system defroster mode is ON all the time.
    • The tires are improperly inflated.
    • Heavy loads are frequently being carried.
    • Heavy acceleration and high speeds are common.
    • Frequent short trips
    • Prolonged periods of idling
    • Driving on unpaved or rough roads

Fuel Odor

    • The pressure relief valve in the fill limiter vent valve (FLVV) is stuck open.
    • The pressure relief valve in the FLVV is leaking.
    • The EVAP canister is saturated with fuel.
    • A leak with the fuel tank, lines and hoses, or fuel filler cap.

Poor Fuel Fill Quality

Test for the following conditions that are applicable to the current symptom:

Difficult to fill/Pre-mature shut-off of the fuel dispensing nozzle

    • The fuel filler pipe check valve is stuck closed.
    • The fill limiter vent valve (FLVV) on the EVAP canister is stuck closed.
    • The EVAP canister air filter is restricted or dirty.
    • Any restricted vapor lines or hoses
    • The EVAP canister has an internal blockage or restriction.
    • A fuel with high reid vapor pressure characteristics.
    • A high fuel temperature
    • The fuel filler hose/pipe is pinched, kinked, or blocked.
    • A condition with the internal components of the fuel tank assembly.
        For more information, refer to the following:

Sudden Over Fill and Spillage

    • The pressure relief valve in the fill limiter vent valve (FLVV) is stuck open.
    • The pressure relief valve in the FLVV is leaking.
    • The FLVV is stuck open.
    • The FLVV is leaking.
       -  Evaporative Emissions Hose Routing Diagram
       -  Fuel System Description
       -  Evaporative Emission Control System Description