GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The intake air temperature (IAT) sensor 2 is a variable resistor. The IAT sensor 2 has a signal circuit and a low reference circuit. The IAT sensor 2 measures the temperature of the air entering the induction system. The powertrain control module (PCM) supplies 5 volts to the IAT signal circuit and a ground for the IAT low reference circuit. When the IAT is cold, the sensor resistance is high. When the air temperature increases, the sensor resistance decreases. With high sensor resistance, the PCM detects a high voltage on the IAT signal circuit. With lower sensor resistance, the PCM detects a lower voltage on the IAT signal circuit. If the PCM detects an excessively low IAT signal voltage, indicating a high temperature, DTC P0097 sets.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0097 Intake Air Temperature (IAT) Sensor 2 Circuit Low Voltage

Conditions for Running the DTC

    • DTCs  P0117, P0118, P0502, and P0503 are not set.
    • The engine run time is more than 10 seconds.
    • The vehicle speed sensor (VSS) indicates that vehicle speed is more than 40 km/h (25 mph).
    • The engine coolant temperature (ECT) is less than 110°C (230°F).
    • This DTC runs continuously within the enabling conditions in a 250 ms loop.

Conditions for Setting the DTC

The PCM detects that the IAT sensor 2 parameter is more than 149°C (300°F) for more than 5 seconds.

Action Taken When the DTC Sets

    • The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.
    • The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records.

Conditions for Clearing the MIL/DTC

    • The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
    • A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
    • A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
    • Clear the MIL and the DTC with a scan tool.

Step

Action

Values

Yes

No

Schematic Reference: Engine Controls Schematics

Connector End View Reference: Powertrain Control Module Connector End Views or Engine Controls Connector End Views

1

Did you perform the Diagnostic System Check - Vehicle?

--

Go to Step 2

Go to Diagnostic System Check - Vehicle

2

Observe the IAT sensor 2 parameter with a scan tool.

Is the IAT sensor 2 parameter more than the specified value?

149°C (300°F)

Go to Step 4

Go to Step 3

3

  1. Observe the Freeze Frame/Failure Records for this DTC.
  2. Turn OFF the ignition for 90 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.

Did the DTC fail this ignition?

--

Go to Step 4

Go to Testing for Intermittent Conditions and Poor Connections

4

  1. Disconnect the intake air temperature (IAT) sensor 2.
  2. Observe the IAT sensor 2 parameter with a scan tool.

Is the IAT sensor 2 parameter less than the specified value?

-39°C (-38°F)

Go to Step 6

Go to Step 5

5

Test the signal circuit of the IAT sensor 2 for a short to ground or a short to the IAT sensor 2 low reference circuit. Refer to Circuit Testing and Wiring Repairs.

Did you find and correct the condition?

--

Go to Step 10

Go to Step 7

6

Test for an intermittent and for a poor connection at the IAT sensor 2. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs.

Did you find and correct the condition?

--

Go to Step 10

Go to Step 8

7

Test for an intermittent and for a poor connection at the powertrain control module (PCM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs.

Did you find and correct the condition?

--

Go to Step 10

Go to Step 9

8

Replace the IAT sensor 2. Refer to Intake Air Temperature Sensor Replacement .

Did you complete the replacement?

--

Go to Step 10

--

9

Replace the PCM. Refer to Control Module References for replacement, setup, and programming.

Did you complete the replacement?

--

Go to Step 10

--

10

  1. Clear the DTCs with a scan tool.
  2. Turn OFF the ignition for 90 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.

Did the DTC fail this ignition?

--

Go to Step 2

Go to Step 11

11

Observe the Capture Info with a scan tool.

Are there any DTCs that have not been diagnosed?

--

Go to Diagnostic Trouble Code (DTC) List - Vehicle

System OK