GM Service Manual Online
For 1990-2009 cars only

Circuit Description

Heated oxygen sensors (HO2S) are used for fuel control and post catalyst monitoring. Each HO2S compares the oxygen content of the surrounding air with the oxygen content in the exhaust stream. The HO2S must reach operating temperature to provide an accurate voltage signal. Heating elements inside the HO2S minimize the time required for the sensors to reach operating temperature. The engine control module (ECM) supplies the HO2S with a reference, or bias, voltage of about 450 mV. When the engine is first started the ECM operates in Open Loop, ignoring the HO2S voltage signal. Once the HO2S reaches operating temperature and Closed Loop is achieved, the HO2S generates a voltage within a range of 0-1,000 mV that fluctuates above and below bias voltage. High HO2S voltage indicates a rich exhaust stream, and low HO2S voltage indicates a lean exhaust stream. If the ECM detects an HO2S 1 voltage that stays below a specified value, DTC P0131 will set.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0131 Circuit Low Voltage Sensor 1

Conditions For Running The DTC

    • DTCs P0106, P0107, P0108, P0112, P0113, P0117, P0118, P0122, P0123, P0125, P0171, P0172, P0300, P0336, P0340, P0341, P0455, P0500, P0601, P0602, P0606, P0641, P0722, P0723 are not set.
    • The Loop Status parameter is closed.
    • The Air Fuel Ratio parameter is between 14.5:1 and 14.8:1.
    • The transmission is in Drive with automatic transmission.
    • DTC P0131 runs continuously when the above conditions are met.

Conditions For Setting The DTC

Lean Test

    • The ECM detects that the HO2S 1 voltage parameter is less than 291 mV.
    • DTC P0131 sets during the lean test within 100 seconds when the above condition is met.

OR

Power Enrichment Test

    • The ECM detects that the HO2S 1 voltage parameter is less than 291 mV.
    • DTC P0131 sets during the power enrichment test within 10 seconds when the above condition is met.

Action Taken When the DTC Sets

    • The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.
    • The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records.
    • The control module commands the Loop Status open.

Conditions for Clearing the MIL/DTC

    • The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
    • A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
    • A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
    • Clear the MIL and the DTC with a scan tool.

Test Description

The number below refers to the step number on the diagnostic table.

  1. If the voltage is varying above and below the specified range, the condition is not present.

Step

Action

Values

Yes

No

Schematic Reference: Engine Controls Schematics

Connector End View Reference: Engine Controls Connector End Views or Engine Control Module Connector End Views

1

Did you perform the Diagnostic System Check - Vehicle?

--

Go to Step 2

Go to Diagnostic System Check - Vehicle

2

  1. Start the engine.
  2. Allow the engine to reach operating temperature. Refer to Scan Tool Data List .
  3. Increase the engine speed to 2,000 RPM.
  4. Observe the HO2S 1 voltage parameter with a scan tool.

Is the HO2S 1 voltage parameter varying above and below the specified range?

300-600 mV

Go to Step 3

Go to Step 4

3

  1. Observe the Freeze Frame/Failure Records for this DTC.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.

Did the DTC fail this ignition?

--

Go to Step 4

Go to Testing for Intermittent Conditions and Poor Connections

4

  1. Turn OFF the ignition.
  2. Disconnect the heated oxygen sensor (HO2S) 1.
  3. Turn ON the ignition, with the engine OFF.
  4. Observe the HO2S 1 voltage parameter with a scan tool.

Is the HO2S 1 voltage parameter less than the specified value?

100 mV

Go to Step 5

Go to Step 7

5

Test the HO2S 1 high signal circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

--

Go to Step 10

Go to Step 6

6

Test the HO2S 1 high signal circuit for a short to the HO2S 1 low signal circuit. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

--

Go to Step 10

Go to Step 9

7

  1. The HO2S 1 may be detecting a lean exhaust condition or may be contaminated. Inspect for the following conditions:
  2. Notice: Refer to Silicon Contamination of Heated Oxygen Sensors Notice in the Preface section.

    • A silicon contaminated HO2S 1
    • Any water intrusion into the HO2S 1 connector
    • An exhaust leak between the HO2S 1 and the engine
    • Any vacuum leaks
    • An inaccurate manifold absolute pressure (MAP) sensor--Refer to DTC P0106 .
    • An incorrect fuel pressure--Refer to Fuel System Diagnosis .
    • Any lean fuel injectors--Refer to Fuel Injector Diagnosis .
  3. Repair any of the above or similar engine conditions as necessary.

Did you find and correct the condition?

--

Go to Step 10

Go to Step 8

8

Replace the HO2S 1. Refer to Heated Oxygen Sensor 1 Replacement .

Did you complete the replacement?

--

Go to Step 10

--

9

Replace the engine control module (ECM). Refer to Control Module References for replacement, setup, and programming.

Did you complete the replacement?

--

Go to Step 10

--

10

  1. Clear the DTCs with a scan tool.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.

Did the DTC fail this ignition?

--

Go to Step 2

Go to Step 11

11

In order to ensure that the performance of the catalyst has not been affected by the fault that set this DTC, operate the vehicle within the conditions for running and setting DTC P0420 and verify that P0420 runs and passes. Refer to DTC P0420 .

Does the DTC run and pass?

--

Go to Step 12

Go to DTC P0420

12

Observe the Capture Info with a scan tool.

Are there any DTCs that have not been diagnosed?

--

Go to Diagnostic Trouble Code (DTC) List - Vehicle

System OK