GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Pontiac 🢒 2000 🢒 Montana 🢒 Restraints 🢒 SIR 🢒 DTC B0041 LF/Driver Side Deployment Loop Open

Object Number: 552714 Size: SF
SIR Components
Sensors, Pretensioners, and Side Air Bags
Handling ESD Sensitive Parts Notice
SIR Caution

Circuit Description

When you first turn ON the ignition, the inflatable restraint sensing and diagnostic module (SDM) performs tests to diagnose critical malfunctions within itself. Then the SDM performs the following continuous diagnostic tests on the deployment loops:

    • Deployment loop voltage out of range test
    • Deployment loop resistance measurement test

If the voltage out of range test detects a short to voltage condition, the resistance measurement test for that deployment loop will not be performed.

Conditions for Running the DTC

Deployment loop voltage out of range test:

    • Ignition 1 voltage is within the normal operating voltage range.
    • Driver side deployment loop is not shorted to voltage.
    • Driver side high terminal B1 is less than 2 volts.

Deployment loop resistance measurement test:

    • Ignition 1 voltage is within the normal operating voltage range.
    • Driver side deployment loop is not shorted to voltage.
    • Driver side deployment loop is not shorted to ground.

Conditions for Setting the DTC

Deployment loop voltage out of range test - Driver side deployment loop resistance is at least 6 ohms for 300 milliseconds.

Deployment loop resistance measurement test - Driver side deployment loop resistance is more than 3.7 ohms for 300 milliseconds.

Action Taken When the DTC Sets

The SDM commands ON the AIR BAG warning lamp via Class 2 serial data.

Conditions for Clearing the DTC
    • You can issue a CLEAR CODES command
    • A history DTC will clear once 255 malfunction free ignition cycles have occurred

Diagnostic Aids

The following can cause an intermittent condition:

    • The inflatable restraint side impact module - LH yellow 2-way connector.
    • The SDM wiring harness connector.
    • The wire to terminal connections in the driver side high circuit.
    • The wire to terminal connections in the driver side low circuit.
    • Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.

Test Description

The number(s) below refer to the step number(s) on the diagnostic table.

  1. This step checks the inflatable restraint side impact module - LH yellow 2-way connector.

    2.

  2. This step checks to see if there is a malfunctioning inflatable restraint side impact module - LH.

    3.

  3. This step checks to see if there is an open or a high resistance in the driver side high circuit.

    4.

  4. This step determines if there is an open or a high resistance in the driver side low circuit or if there is a malfunctioning SDM.

Step

Action

Value(s)

Yes

No

1

Did you perform A Diagnostic System Check - SIR?

--

Go to Step 2

Go to Diagnostic System Check - SIR

2

  1. Turn OFF the ignition.
  2. Disconnect the inflatable restraint side impact module - LH yellow 2-way connector. Refer to Inflatable Restraint Side Impact Module Replacement - Left Side .
  3. Inspect the component and harness sides of the inflatable restraint side impact module - LH yellow 2-way connector for the following conditions:
    4. • Corrosion
    • Damaged terminals
    • Poor connections/terminal tension
  4. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.

Does either the component or harness side of the inflatable restraint side impact module - LH yellow 2-way connector exhibit any signs of corrosion, terminal damage, or poor connections?

--

Go to Step 3

Go to Step 4

3
  1. If the component side of the inflatable restraint side impact module - LH yellow 2-way connector is damaged, the inflatable restraint side impact module - LH must be replaced.
  2. If the harness side of the inflatable restraint side impact module - LH yellow 2-way connector is damaged, replace the harness side of the connector. Refer to Connector Repairs in Wiring systems.

Did you complete the repair?

--

Go to Step 12

--

4
  1. Reconnect the inflatable restraint side impact module - LH yellow 2-way connector.
  2. Verify that the connector position assurance (CPA) is properly installed.
  3. Turn ON the ignition, with the engine OFF.
  4. Use the scan tool to request the SIR DTC display.

Does the scan tool indicate that this DTC is current?

--

Go to Step 5

Go to Diagnostic Aids

5

  1. Turn OFF the ignition.
  2. Disconnect the inflatable restraint side impact module - LH yellow 2-way connector.
  3. Use the J 38715-5 adaptor to connect the J 38715-A SIR Driver/Passenger Load Tool STEERING WHEEL connector to the harness side of the inflatable restraint side impact module - LH yellow 2-way connector.
  4. Turn ON the ignition, with the engine OFF.
  5. Use the scan tool to request the SIR DTC display.

Does the scan tool indicate that this DTC is current?

--

Go to Step 7

Go to Step 6

6
  1. Turn OFF the ignition.
  2. Replace the inflatable restraint side impact module - LH. Refer to Inflatable Restraint Side Impact Module Replacement - Left Side .

Did you complete the replacement?

--

Go to Step 12

--

7

  1. Turn OFF the ignition.
  2. Remove the J 38715-A .
  3. Disconnect the inflatable restraint sensing and diagnostic module (SDM). Refer to Inflatable Restraint Sensing and Diagnostic Module Replacement .
  4. Use the J 39200 Digital Multimeter (DMM) to measure the resistance of the driver side high circuit.

Does the resistance measure less than the specified value?

0.5 ohms

Go to Step 9

Go to Step 8

8

Locate and repair the open or the high resistance in the driver side high circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you complete the repair?

--

Go to Step 12

--

9

Use the DMM to measure the resistance of the driver side low circuit.

Does the resistance measure less than the specified value?

0.5 ohms

Go to Step 11

Go to Step 10

10

Locate and repair the open or the high resistance in the driver side low circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you complete the repair?

--

Go to Step 12

--

11

Replace the SDM. Refer to Inflatable Restraint Sensing and Diagnostic Module Replacement .

Did you complete the replacement?

--

Go to Step 12

--

12
  1. Reconnect all SIR components.
  2. Verify that all components and connectors are properly mounted.
  3. Turn ON the ignition, with the engine OFF.
  4. Use the scan tool in order to clear the DTCs.

Did you complete the action?

--

Go to Diagnostic System Check - SIR

--