| Table 1: | Electronic Brake Control Module Scan Tool Data Parameters |
| Table 2: | Electronic Brake Control Module Scan Tool Output Controls |
Parameter | Expected Value | Definition |
|---|---|---|
Operating Conditions: Ignition ON | ||
ABS Active | No | The scan tool displays Yes or No. The scan tool will display Yes when the ABS is active and No during normal vehicle operation. |
ABS Warning Lamp | Off | The scan tool will display On or Off depending on the state of the ABS indicator. |
BPMV Pressure Sensor | 0.0 Bar | The scan tool will display BAR or PSI. This is a reading of the pressure applied to brake pedal. |
Brake Switch | Released | The scan tool displays Applied or Released. This is the state of the brake pedal. |
DRP Active | No | The scan tool displays Yes or No. This is the state of the dynamic rear proportioning (DRP). |
DRP Disabled | No | The scan tool displays Yes or No. This is the state of the dynamic rear proportioning (DRP). |
EBTCM to PCM Requested Torque | 0 N·m | The scan tool displays the Requested Torque signal in N·m. |
Engine Speed | 0 RPM | The scan tool displays the current engine speed in RPM. |
Ignition Voltage | Varies | The scan tool displays 0-17 Volts. The scan tool displays the level of ignition voltage at the EBCM. |
Lateral Accelerometer Sensor | 0 g | The scan tool will display 0 g. The scan tool displays the lateral accelerometer signal received from the sensor. |
Left Front Wheel Speed | 0 km/h (0 mph) | This displays km/h (mph). This is the current speed of the left front wheel speed sensor. |
LF Inlet Valve Solenoid | Inactive | The scan tool will display Active or Inactive. The scan tool displays the commanded state of the LF inlet solenoid valve. |
LF Outlet Valve Solenoid | Inactive | The scan tool will display Active or Inactive. The scan tool displays the commanded state of the LF outlet solenoid valve. |
LF TCS Isolation Solenoid | Inactive | The scan tool will display Active/Inactive. This displays the commanded state of the solenoid valve. |
LF TCS Prime Solenoid | Inactive | The scan tool will display Active/Inactive. This displays the commanded state of the solenoid valve. |
Left Rear Wheel Speed | OK | The scan tool displays OK or Low. This is the state of the washer fluid level. |
Low Traction Lamp | Off | The scan tool will display On/Off. This will indicate the state of the Low Traction Indicator. |
LR Inlet Valve Solenoid | Off | The scan tool displays Active or Inactive. The scan tool displays the commanded state of the LR inlet solenoid valve. |
LR Outlet Valve Solenoid | Off | The scan tool displays Active or Inactive. The scan tool displays the commanded state of the LR outlet solenoid valve. |
Motor Relay State | Off | The scan tool display On /Off. This is the commanded state of the ABS pump motor relay. |
PCM to EBTCM Delivered Torque | 0 N·m | The scan tool displays the Delivered Torque signal in N·m |
RF Inlet Valve Solenoid | Off | The scan tool displays Active or Inactive. The scan tool displays the commanded state of the RF inlet solenoid valve. |
RF Outlet Valve Solenoid | Off | The scan tool displays Active or Inactive. The scan tool displays the commanded state of the RF outlet solenoid valve. |
RF TCS Isolation Solenoid | Inactive | The scan tool will display Active/Inactive. This displays the commanded state of the solenoid valve. |
RF TCS Prime Solenoid | Inactive | The scan tool will display Active/Inactive. This displays the commanded state of the solenoid valve. |
Right Front Wheel Speed | 0 km/h (0 mph) | This displays km/h (mph). This is the current speed of the right front wheel speed sensor. |
Rough Road Parameter | 0g | The scan tool will display 0-g. The scan tool displays the EBCM calculation of the road surface roughness. This information is sent to the engine controller via a serial data message to be used for misfire detection. |
RR Inlet Valve Solenoid | Off | The scan tool displays Active or Inactive - The scan tool displays the commanded state of the RR inlet solenoid valve. |
RR Outlet Valve Solenoid | Off | The scan tool displays Active or Inactive - The scan tool displays the commanded state of the RR outlet solenoid valve. |
Right Rear Wheel Speed | 0 km/h (0 mph) | This displays km/h (mph). This is the current speed of the right front wheel speed sensor. |
Speed Range 1 Calibrated | Yes | The scan tool displays Yes or No. Yes indicates speed range 1 is fully calibrated and the TPM system has full tire pressure detection capability from 31-65 km/h (19-40 mph). No indicates the TPM system is in the calibration process in speed range 1 and has no tire pressure detection capability in speed range 1. |
Speed Range 1 Tire Pressure | No | The scan tool displays Yes or No. Yes indicates the TPM system has detected a low tire pressure condition in speed range 1. No indicates the TPM system has not detected a low tire pressure condition in speed range 1. |
Speed Range 2 Calibrated | Yes | The scan tool displays Yes or No. Yes indicates speed range 2 is fully calibrated and the TPM system has full tire pressure detection capability from 65-95 km/h (40-59 mph). No indicates the TPM system is in the calibration process in speed range 2 and has no tire pressure detection capability in speed range 2. |
Speed Range 2 Tire Pressure | No | The scan tool displays Yes or No. Yes indicates the TPM system has detected a low tire pressure condition in speed range 2. No indicates the TPM system has not detected a low tire pressure condition in speed range 2. |
Speed Range 3 Calibrated | Yes | The scan tool displays Yes or No. Yes indicates speed range 3 is fully calibrated and the TPM system has full tire pressure detection capability from 95-120 km/h (59-74.5 mph). No indicates the TPM system is in the calibration process in speed range 3 and has no tire pressure detection capability in speed range 3. |
Speed Range 3 Tire Pressure | No | The scan tool displays Yes or No. Yes indicates the TPM system has detected a low tire pressure condition in speed range 3. No indicates the TPM system has not detected a low tire pressure condition in speed range 3. |
Speed Range 4 Calibrated | Yes | The scan tool displays Yes or No. Yes indicates speed range 4 is fully calibrated and the TPM system has full tire pressure detection capability from 120-145 km/h (74.5-90 mph). No indicates the TPM system is in the calibration process in speed range 4 and has no tire pressure detection capability in speed range 4. |
Speed Range 4 Tire Pressure | No | The scan tool displays Yes or No. Yes indicates the TPM system has detected a low tire pressure condition in speed range 4. No indicates the TPM system has not detected a low tire pressure condition in speed range 4. |
TCS Active | No | The scan tool displays Yes or No. The scan tool will display Yes when the traction control system is active and No during normal vehicle operation. |
TCS Switch State | On | The scan tool displays On/Off. The scan tool will display the state of the Traction Control Switch. |
TCS Warning Lamp | Off | The scan tool will display On or Off depending on the state of the TCS indicator. |
TPM Indicator/Message | Off | The scan tool displays On or Off indicated if the TPM is currently requesting a warning lamp to illuminate or a message to be displayed. |
TPM System Enabled | Yes | The scan tool displays Yes, or No. Yes indicates the TPM System has been enabled in the RCDLR. No indicates the TPM System has not been enabled in the RCDLR. |
Valve Relay State | Off | The scan tool will display On/Off depending on the state of the VSES relay. |
VES Auto Learn Complete | Yes | The scan tool will display YES/NO depending if the VSES auto learn is completed. |
VES Malfunction | Not Set | The scan tool displays Set or Not Set. |
VSES Active | No | The scan tool displays Yes or No. The scan tool displays Yes when VSES is active, and No when VSES is inactive. |
VSES Failed | No | The scan tool will display Yes or No depending on the state of the VSES system. |
VES Steering Angle Sensor | Varies | The scan tool displays -720° to approximately +720°. The scan tool will display the signal received from the Steering Angle Sensor. |
Yaw Rate Sensor | 0.0 °/sec | The scan tool displays 0.0°/sec. The scan tool displays the signal received from the yaw rate sensor . |
Scan Tool Output Control | Description |
|---|---|
Automated Bleed | This is used in order to bleed ABS hydraulics. Refer to Antilock Brake System Automated Bleed Procedure . |
LF Inlet Valve Solenoid | Commands the solenoid ON and OFF. |
LF Outlet Valve Solenoid | Commands the solenoid ON and OFF. |
LR Inlet Valve Solenoid | Commands the solenoid ON and OFF. |
LR Outlet Valve Solenoid | Commands the solenoid ON and OFF. |
RF Inlet Valve Solenoid | Commands the solenoid ON and OFF. |
RF Outlet Valve Solenoid | Commands the solenoid ON and OFF. |
RR Inlet Valve Solenoid | Commands the solenoid ON and OFF. |
RR Outlet Valve Solenoid | Commands the solenoid ON and OFF. |
Steering Angle Sensor Centering | Performs the steering wheel centering procedure. |
