GM Service Manual Online
For 1990-2009 cars only

Tools Required

    •  J 37872 Compressor Clutch Holding Tool
    •  J 6083 Snap Ring Pliers
    •  J 39400-A Halogen Leak Detector

Removal Procedure

  1. Remove the A/C compressor for the 5.3L engine. Refer to Air Conditioning Compressor Replacement .
  2. Remove the accessory drive belt from the A/C compressor on the 3.8L engine. Refer to Drive Belt Replacement .
  3. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .
  4. Remove the lower air deflector. Refer to Radiator Air Lower Baffle and Deflector Replacement .

  5. Object Number: 872553  Size: SH

    Important: Remove the three adjustable dowels from J 37872 .

    Install three 5/16x1 inch bolts in place of the dowels.

  6. Remove and discard the compressor clutch plate bolt.
  7. Use the J 37872 to hold the compressor clutch plate from turning.


    Object Number: 872556  Size: SH
  8. Remove the compressor clutch plate from the compressor.

  9. Object Number: 872558  Size: SH
  10. Remove the compressor pulley snap ring using the J 6083 .

  11. Object Number: 872560  Size: SH
  12. Remove the compressor pulley from the compressor.

  13. Object Number: 872563  Size: SH
  14. Remove the compressor clutch coil snap ring using the J 6083 .

  15. Object Number: 872561  Size: SH
  16. Remove the compressor clutch coil from the compressor.

Installation Procedure

  1. Carefully clean the clutch plate bolt threads with a M6x1.0 tap. Carefully blow out debris with compressed air.

  2. Object Number: 872561  Size: SH
  3. Install the compressor clutch coil to the compressor.

  4. Object Number: 872563  Size: SH
  5. Install the compressor clutch coil snap ring using the J 6083 .

  6. Object Number: 872560  Size: SH
  7. Install the compressor pulley to the compressor.

  8. Object Number: 872558  Size: SH
  9. Install the compressor pulley snap ring using the J 6083 .
  10. Place a small amount of oil on the 0.4 mm (0.016 in) air gap shim and place inside the clutch drive plate.

  11. Object Number: 872556  Size: SH
  12. Install the compressor clutch plate to the compressor.

  13. Object Number: 187363  Size: SH

    Important: Make certain that the drive plate does not drag against the pulley when the pulley is rotated.

  14. Measure the air gap between the pulley and the drive plate. Adjust the shims to achieve a 0.3-0.6 mm (0.012-0.024 in) air gap.
  15. Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 872553  Size: SH

    Important: Make certain that the new drive plate bolt has colored adhesive on at least 5 threads.

  16. Install the clutch drive plate bolt.
  17. Tighten the compressor clutch drive plate bolt.
  18. Use the J 37872 to hold the compressor clutch plate from turning.

    Tighten
    Tighten the bolt to 12 N·m (106 lb in).

  19. Install the lower air deflector. Refer to Radiator Air Lower Baffle and Deflector Replacement .
  20. Lower the vehicle.
  21. Install the accessory drive belt to the A/C compressor on the 3.8L engine. Refer to Drive Belt Replacement .
  22. Install the A/C compressor for the 5.3L engine. Refer to Air Conditioning Compressor Replacement .
  23. Leak test the fittings using the J 39400-A .