GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The powertrain control module (PCM) monitors the high side refrigerant pressure through a air conditioning (A/C) refrigerant pressure sensor. When the pressure is high the signal voltage is high. When the pressure is low the signal voltage is low. When pressure is high the PCM commands the cooling fans ON. When pressure is too high or too low the PCM will not allow the A/C compressor clutch to engage.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0530 Air Conditioning Refrigerant Pressure Sensor Circuit

Conditions for Running the DTC

The PCM detects the signal circuit is less than 5 counts (0.09 volts) or more than 250 counts (4.90 volts).

Conditions for Setting the DTC

The condition exists for 20 seconds.

Action Taken When the DTC Sets

    • The PCM will not illuminate the malfunction indicator lamp (MIL).
    • The PCM stores the failure records.
    • The A/C compressor clutch is disabled.

Conditions for Clearing the DTC

    • The DTC will become history if the PCM no longer detects a failure.
    • The history DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
    • The DTC can be cleared with a scan tool.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. Tests for the proper operation of the circuit in the low voltage range.

  2. Tests for the proper operation of the circuit in the high voltage range. If the fuse in the jumper opens when you perform this test, the signal circuit is shorted to ground.

  3. Tests for a short to voltage in the 5-volt reference circuit.

  4. Tests for a high resistance or an open in the low reference circuit.

  5. Perform the programming procedure for the PCM.

Step

Action

Values

Yes

No

Schematic Reference: HVAC Schematics

Connector End View Reference: HVAC Connector End Views

1

Did you perform the Diagnostic System Check - Vehicle?

--

Go to Step 2

Go to Diagnostic System Check - Vehicle

2

Important: The ambient air temperature must be above 3°C (38°F).

  1. Turn OFF the ignition.
  2. Inspect the air conditioning (A/C) compressor for free rotation operation.
  3. Start the engine.
  4. Place the HVAC control module in the OFF position.

Does the A/C compressor operate?

--

Go to HVAC Compressor Clutch Does Not Disengage

Go to Step 3

3

  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With the scan tool, observe the A/C High Side Pressure parameter in the Powertrain Control module engine data 2 list.

Does the scan tool indicate that the A/C High Side Pressure parameter is within the specified range?

0.09-4.90 V

Go to Testing for Intermittent Conditions and Poor Connections

Go to Step 4

4

  1. Turn OFF the ignition.
  2. Disconnect the A/C refrigerant pressure sensor.
  3. Turn ON the ignition, with the engine OFF.
  4. With a scan tool, observe the A/C High Side Pressure parameter.

Does the scan tool indicate that the A/C High Side Pressure parameter is less than the specified value?

0.09 V

Go to Step 5

Go to Step 11

5

  1. Turn OFF the ignition.
  2. Connect a 3-amp fused jumper wire between the 5-volt reference circuit of the A/C refrigerant pressure sensor and the signal circuit of the A/C refrigerant pressure sensor.
  3. Turn ON the ignition, with the engine OFF.
  4. With a scan tool, observe the A/C High Side Pressure parameter.

Does the scan tool indicate that the A/C High Side Pressure parameter is more than the specified value?

4.90 V

Go to Step 6

Go to Step 9

6

  1. Disconnect the fused jumper wire.
  2. Measure the voltage between the 5-volt reference circuit of the A/C refrigerant pressure sensor and the low reference circuit of the A/C refrigerant pressure sensor.

Does the voltage measure less than the specified value?

5.1 V

Go to Step 7

Go to Step 8

7

  1. Turn OFF the ignition.
  2. Disconnect the negative battery cable.
  3. Measure the resistance from the low reference circuit of the A/C refrigerant pressure sensor to a good ground.

Does the resistance measure less than the specified value?

5 ohms

Go to Step 13

Go to Step 12

8

Test the 5-volt reference circuit of the A/C refrigerant pressure sensor for a short to voltage. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

--

Go to Step 17

Go to Step 14

9

Test the 5-volt reference circuit of the A/C refrigerant pressure sensor for a short to ground, a high resistance, or an open. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

--

Go to Step 17

Go to Step 10

10

Test the signal circuit of the A/C refrigerant pressure sensor for a short to ground, a high resistance, or an open. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

--

Go to Step 17

Go to Step 14

11

Test the signal circuit of the A/C refrigerant pressure sensor for a short to voltage. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

--

Go to Step 17

Go to Step 14

12

  1. Disconnect the powertrain control module (PCM).
  2. Test the low reference circuit of the A/C refrigerant pressure sensor for a high resistance or an open. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

--

Go to Step 17

Go to Step 14

13

Inspect for poor connections at the harness connector of the A/C refrigerant pressure sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

--

Go to Step 17

Go to Step 15

14

Inspect for poor connections at the harness connector of the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

--

Go to Step 17

Go to Step 16

15

Replace the A/C refrigerant pressure sensor. Refer to Air Conditioning (A/C) Refrigerant Pressure Sensor Replacement .

Did you complete the replacement?

--

Go to Step 17

--

16

Replace the PCM. Refer to Control Module References for replacement, setup, and programming.

Did you complete the replacement?

--

Go to Step 17

--

17

  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.

Does the DTC reset?

--

Go to Step 2

System OK