GM Service Manual Online
For 1990-2009 cars only

Exhaust Manifold Replacement - Left Side RPOs L26/L32

Removal Procedure

  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
  2. Remove the fuel injector sight shield. Refer to Fuel Injector Sight Shield Replacement .
  3. Remove the engine mount struts. Refer to Engine Mount Strut Replacement - Right Side and Engine Mount Strut Replacement - Left Side .
  4. Remove the lower right engine mount strut bracket. Refer to Engine Mount Strut Bracket Replacement - Right Side .

  5. Object Number: 153576  Size: MH
  6. Remove the exhaust crossover pipe bolts from the left exhaust manifold.
  7. Remove the left spark plugs from cylinders 1, 3 and 5. Refer to Spark Plug Replacement .
  8. Remove the oil level indicator tube. Refer to Oil Level Indicator and Tube Replacement .

  9. Object Number: 153577  Size: SH
  10. Remove the left engine lift bracket bolt and the nut.
  11. Remove the left engine lift bracket

  12. Object Number: 153578  Size: SH
  13. Remove the exhaust manifold heat shield nuts.
  14. Remove the exhaust manifold heat shield.

  15. Object Number: 97756  Size: SH
  16. Remove the exhaust manifold bolts and the nuts.
  17. Remove the exhaust manifold.
  18. Remove the exhaust manifold gasket.
  19. Clean and inspect the left exhaust manifold. Refer to Exhaust Manifold Cleaning and Inspection .

Installation Procedure


    Object Number: 97756  Size: SH
  1. Install the new exhaust manifold gasket.
  2. Install the exhaust manifold.
  3. Notice: Refer to Fastener Notice in the Preface section.

  4. Install the exhaust manifold bolts and the nuts.
  5. Tighten
    Tighten the bolts and the nuts to 30 N·m (22 lb ft).


    Object Number: 153578  Size: SH
  6. Install the exhaust manifold heat shield.
  7. Install the exhaust manifold heat shield nuts.
  8. Tighten
    Tighten the nuts to 20 N·m (15 lb ft).


    Object Number: 153577  Size: SH
  9. Install the engine lift bracket.
  10. Install the engine lift bracket bolt and the nut.
  11. Tighten
    Tighten the bolt and the nut to 30 N·m (22 lb ft).

  12. Install the oil level indicator tube. Refer to Oil Level Indicator and Tube Replacement .
  13. Install the left spark plugs to cylinders 1, 3 and 5. Refer to Spark Plug Replacement .

  14. Object Number: 153576  Size: MH
  15. Install the exhaust crossover bolts to the left exhaust manifold.
  16. Tighten
    Tighten the bolts to 20 N·m (15 lb ft).

  17. Install the lower right engine mount strut bracket. Refer to Engine Mount Strut Bracket Replacement - Right Side .
  18. Install the engine mount struts. Refer to Engine Mount Strut Replacement - Right Side and Engine Mount Strut Replacement - Left Side .
  19. Install the fuel injector sight shield. Refer to Fuel Injector Sight Shield Replacement .
  20. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .

Exhaust Manifold Replacement - Left Side RPO LS4

Removal Procedure


    Object Number: 1554543  Size: SH
  1. Remove the engine sight shield. Refer to Upper Intake Manifold Sight Shield Replacement .
  2. Remove the exhaust crossover pipe heat shield in order to access the cross pipe to the exhaust manifold nuts.
  3. Remove the exhaust crossover pipe nuts from the left exhaust manifold.
  4. Remove the left side spark plugs. Refer to Spark Plug Replacement .
  5. Remove the oil level indicator tube. Refer to Oil Level Indicator and Tube Replacement .

  6. Object Number: 1411884  Size: SH
  7. Remove the exhaust manifold heat shield bolts (604).
  8. Remove the exhaust manifold heat shield (603).
  9. Remove the heater hose retainer bolts in order to be able to remove the manifold.

  10. Object Number: 1411880  Size: SH
  11. Remove the exhaust manifold bolts.
  12. Remove the exhaust manifold.
  13. Remove and discard the exhaust manifold gasket.
  14. Clean and inspect the left exhaust manifold. Refer to Exhaust Manifold Cleaning and Inspection .

Installation Procedure

Important: 

   • Tighten the exhaust manifold bolts as specified in the service procedure. Improperly installed and/or leaking exhaust manifold gaskets my affect vehicle emissions and/or On Board Diagnostic (OBD) II system performance.
   • The cylinder head exhaust manifold bolt hole threads must be clean and free of debris or threadlocking material.
   • DO NOT apply threadlock to the first three thread of the bolts.


    Object Number: 1411880  Size: SH
  1. Apply a 5 mm (0.2 in) wide band of threadlock GM P/N 12345493 (Canadian P/N 10953488) or equivalent to the threads of the exhaust manifold bolts.
  2. Notice: Refer to Fastener Notice in the Preface section.

  3. Install a NEW exhaust manifold gasket, the exhaust manifold and bolts.
  4. Tighten

        • Tighten the bolts a first pass to 15 N·m (11 lb ft). Tighten the bolts beginning with the center 2 bolts. Alternate from side to side, and work toward the outside.
        • Tighten the bolts a final pass to 20 N·m (15 lb ft). Tighten the bolts beginning with the center 2 bolts. Alternate from side to side, and work toward the outside.
  5. Using a flat punch, bend over the exposed edge of the exhaust manifold gasket at the rear of the left cylinder head.

  6. Object Number: 1411884  Size: SH
  7. Install the exhaust manifold heat shield (603).
  8. Install the exhaust manifold heat shield bolts (604).
  9. Tighten
    Tighten the bolts to 9 N·m (80 lb in).

  10. Install the oil level indicator tube. Refer to Oil Level Indicator and Tube Replacement .
  11. Install the left side spark plugs. Refer to Spark Plug Replacement .

  12. Object Number: 1554543  Size: SH
  13. Install the exhaust crossover pipe nuts from the left exhaust manifold.
  14. Tighten
    Tighten the nuts to 25 N·m (18 lb ft).

  15. Install the exhaust crossover pipe heat shield.
  16. Install the heater pipe retainer bolts.
  17. Tighten
    Tighten the bolts to 16 N·m (12 lb ft).

  18. Install the engine sight shield. Refer to Upper Intake Manifold Sight Shield Replacement .