Circuit Description
The engine coolant temperature (ECT) sensor is a thermistor mounted in the engine coolant stream. The PCM applies a voltage of approximately 5.0 volts through a pull-up resistor to the ECT signal circuit. When the engine coolant is cold, the sensor, or thermistor, resistance is high, and the PCM will measure a high signal voltage. As the engine coolant warms, the sensor resistance lessens, and the ECT signal voltage measured at the PCM drops. With a fully warmed-up engine, the ECT signal voltage should measure approximately 1.5 volts to 2.0 volts. When the PCM detects an excessively low signal voltage on the engine coolant temperature sensor signal circuit, DTC P0117 will set
Conditions for Running the DTC
The engine run time is more than 3 seconds.
Conditions for Setting the DTC
| • | The ECT sensor signal indicates an engine coolant temperature that is more than 114°C (237°F). |
| • | The above condition present for at least 10 seconds. |
Action Taken When the DTC Sets
| • | The PCM will illuminate the malfunction indicator lamp (MIL) during the second consecutive trip in which the diagnostic test has been run and failed. |
| • | The PCM will store conditions which were present when the DTC set as Freeze Frame/Failure Records data. |
Conditions for Clearing the MIL/DTC
| • | The PCM will turn OFF the malfunction indicator lamp (MIL) during the third consecutive trip in which the diagnostic has run and passed. |
| • | The history DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction. |
| • | The DTC can be cleared by using a scan tool. |
Diagnostic Aids
Inspect for the following conditions:
Many situations may lead to an intermittent condition. Perform each inspection or test as directed.
Important: : Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.
| • | Loose terminal connection |
| - | Use a corresponding mating terminal to test for proper tension. Refer to Testing for Intermittent Conditions and Poor Connections , and to Connector Repairs in Wiring Systems for diagnosis and repair. |
| - | Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and faulty terminal to wire connection. Refer to Testing for Intermittent Conditions and Poor Connections , and to Connector Repairs in Wiring Systems for diagnosis and repair. |
| • | Damaged harness--Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the fault. Refer to Wiring Repairs in Wiring Systems for diagnosis and repair. |
| • | Inspect the powertrain control module (PCM) and the engine grounds for clean and secure connections. Refer to Wiring Repairs in Wiring Systems for diagnosis and repair. |
If the condition is determined to be intermittent, reviewing the Snapshot or Freeze Frame/Failure Records may be useful in determining when the DTC or condition was identified.
Test Description
The numbers below refer to the step numbers on the diagnostic table:
-
This step verifies that the fault is present.
-
If DTC P0117 can be repeated only by duplicating the Failure Records conditions, refer to the Temperature to Resistance Value table. Use this table in order to test the ECT sensor at various temperatures, in order to evaluate the possibility of a shifted sensor that may be shorted above or below a certain temperature. If this occurs, replace the ECT sensor. If the ECT sensor appears OK, the fault is intermittent. Refer to Diagnostic Aids.
-
When the PCM is replaced, you must program the new PCM.
Step | Action | Values | Yes | No |
|---|---|---|---|---|
1 | Did you perform the Powertrain On Board Diagnostic (OBD) System Check? | -- | ||
Is the parameter more than the specified value? | 139°C (282°F) | |||
Does the DTC reset? | -- | Go to Diagnostic Aids | ||
4 |
Is the parameter less than the specified value? | -38°C (-36°F) | ||
5 | Test the ECT Sensor signal circuit for a short to ground, or for a short to the sensor ground circuit. Repair the condition as necessary. Refer to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | ||
6 | Replace the ECT sensor. Refer to Engine Coolant Temperature Sensor Replacement . Did you complete the replacement? | -- | -- | |
|
Important: You must program the replacement PCM. Replace the PCM. Refer to Powertrain Control Module Replacement/Programming . Did you complete the replacement? | -- | -- | ||
8 |
Does the DTC reset? | -- | System OK |
