Refer to Engine Control Schematic
CKP, CMP, ICM and Knock Sensor
.
Circuit Description
During cranking, the IC Module monitors the 7X CKP sensor input for recognition of the sync signal. The sync signal is used only by the IC Module for synchronization at start-up to determine the correct cylinder pair to spark. Once the engine speed reaches approximately 600 RPM the PCM sends 5.0V to the bypass control circuit at the IC Control Module causing the IC control circuit to become ungrounded allowing the 24X signal to be used for better low engine speed performance. At higher engine speeds (1650+) the PCM uses the 3X reference pulses to control ignition timing because a higher resolution signal is not needed.
Conventional ignition coils have one end of the secondary winding connected to the engine ground. In this ignition system, neither end of the secondary winding is grounded. Instead, each end of a coil's secondary winding is attached to a spark plug. Each cylinder is paired with the cylinder that is opposite it (1-4, 2-5, 3-6). These two plugs are on companion cylinders, i.e., on top dead center at the same time. When the coil discharges, both plugs fire at the same time to complete the series circuit. The cylinder on compression is said to be the event cylinder and the one on exhaust is the waste cylinder. The cylinder on the exhaust stroke requires very little of the available energy to fire the spark plug. The remaining energy will be used as required by the cylinder on the compression stroke. The same process is repeated when the cylinders reverse roles. This method of ignition is called a waste spark ignition system.
This table assumes there are no Ignition System, Fuel Injector, Cam Sensor, or Crank Sensor DTC's present. The Electronic Ignition System Check tests for faulty ignition coils, spark plugs, plug wires, the 7X Crank Sensor, and IC Module. This table requires the J 26792 spark tester .
Diagnostic Aids
Inspect for the following conditions:
Important: : Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.
| • | Poor terminal connection. |
| Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and faulty terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to Wiring Systems for diagnosis and repair. |
| • | Damaged harness. |
| Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the fault. Refer to Wiring Systems for diagnosis and repair. |
| • | Inspect the PCM and the engine grounds for clean and secure connections. |
If the DTC is determined to be intermittent, reviewing the Failure Records can be useful in determining when the DTC was last set.
Test Description
Numbers below refer to the step numbers on the Diagnostic Table:
-
The J 26792 spark tester presents a more difficult load on the secondary ignition than a normal spark plug. If a miss, stumble, or hesitation is being caused by a spark plug not firing, the spark tester should also not fire.
-
Use a 5 percent saltwater solution in a spray bottle to induce voltage arching to ground through faulty insulation of spark plug wires.
-
If the no spark condition follows the suspected coil, that coil is faulty. Otherwise, the ignition module is the cause of no spark. This test could also be performed by substituting a known good coil for the one causing the no spark condition.
Step | Action | Value(s) | Yes | No | ||||
|---|---|---|---|---|---|---|---|---|
1 | Did you perform the Powertrain On Board Diagnostic (OBD) System Check? | -- | ||||||
2 |
Does the scan tool indicate 3X reference signal present? | -- | ||||||
Did you observe any non-sparking cylinders? | -- | |||||||
|
Important: It is possible for an arching Spark Plug Wire to IC Module or arching Ignition Coil to IC Module to cause a stall or no start condition. Inspect and test the affected cylinder spark plug wire(s), Ignition coil(s), and spark plugs for a short to ground or arching to ground. If carbon tracking or corrosion is present, replace both components affected. Refer to the following:
Did you find and correct the condition? | -- | |||||||
5 |
Did you find and correct the condition? | 600ohms per ft (1,968ohms per M) | ||||||
Did you find and correct the condition? | -- | |||||||
7 | Inspect the spark plug wires for proper routing and for the correct firing order. If any spark plug wires are found to be misrouted, reroute as necessary. Refer to Spark Plug Wire Harness Replacement in Engine Electrical. Did you find and correct the condition? | -- | ||||||
8 |
Did you find and correct the condition? | -- | ||||||
9 |
Did you complete the replacement? | -- | -- | |||||
10 |
Does the test lamp illuminate? | -- | ||||||
11 | Connect a test lamp between the IC Module ignition feed circuit and IC Module ground circuit. Does the test lamp light? | -- | ||||||
12 |
Does the test lamp illuminate when probing either circuits? | -- | ||||||
13 |
Does the test lamp illuminate when probing either circuits? | -- | ||||||
14 |
Does the DMM indicate AC Duty Cycle present? | -- | ||||||
15 | Test the 7X Crank Sensor circuits for the following conditions:
Repair any damaged wiring. Refer to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | ||||||
16 | Repair the open or short to ground in the IC Module Ignition feed circuit. Refer to Wiring Repairs in Wiring Systems. Replace the fuse if necessary. Did you complete the repair? | -- | -- | |||||
17 | Repair the short to ground in the 7X Reference circuit which illuminated the test lamp. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | -- | |||||
18 | Repair the short to voltage in the 7X Reference circuit which illuminated the test lamp. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | -- | |||||
19 | Repair the open in the IC Module ground circuit. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | -- | |||||
20 | Replace IC Module. Refer to Ignition Control Module Replacement in Engine Controls. Did you complete the replacement? | -- | -- | |||||
21 | Replace the 7X Crank Sensor. Refer to Crankshaft Position Sensor Replacement in Engine Controls. Did you complete the replacement? | -- | -- |
