GM Service Manual Online
For 1990-2009 cars only

Refer to Engine Controls Schematic

HO2S #1 and HO2S #2


Object Number: 588220  Size: FS
Underhood Accessory Wiring Junction Block, Secondary Air Injection PUmp Relay, Secondary Air Injection Valve Solenoid, Supercharger Bypass Valve, Heated Oxygen Sensors, MAF and EVAP
G117
Handling ESD Sensitive Parts Notice
Engine Controls Components
Powertrain Control Module Description
AIR Motor, AIR Valve, AIR Relay and Theft Deterrent Module
A/C Refrigerant Pressure Sensor, TP, MAP, ECT and IAT Sensor
OBD II Symbol Description Notice
.

Circuit Description

Heated oxygen sensors (HO2S) are used to minimize the amount of time required for closed loop fuel control operation and to allow accurate catalyst monitoring. The oxygen sensor heater greatly decreases the amount of time required for fuel control sensor HO2S 1 to become active. The oxygen sensor heater is required by catalyst monitor sensor HO2S 2 to maintain a sufficiently high temperature. This allows accurate exhaust oxygen content readings further from the engine.

The PCM will run the heater test only after a cold start (determined by engine coolant and intake air temperature at the time of start-up) and only once during an ignition cycle. When the engine is started the PCM will monitor the HO2S voltage. When the HO2S voltage indicates a sufficiently active sensor, the PCM looks at how much time has elapsed since startup. If the PCM determines that too much time was required for the HO2S 1 to become active, a DTC P0135 will set. The time it should take the HO2S to reach operating temperature is based on the engine coolant temperature at start up and the average mass air flow since start-up (higher average airflow or higher start-up engine coolant temperature = shorter time to HO2S activity).

Conditions for Running the DTC

    • No active TP, MAP, MAF, ECT, IAT sensor, fuel injector circuit, EVAP, AIR, DTCs present.
    • Intake air temperature (IAT) is less than 35°C (95°F) at start up.
    • Engine coolant temperature (ECT) is less than 35°C (95°F) at start up.
    • IAT and ECT are within 6°C (42°F) of each other at start up.
    • System voltage between 9.0 and 18.0 volts.
    • AIR pump commanded OFF.

Conditions for Setting the DTC

HO2S 1 voltage remains within 150 mV of the bias voltage (about 450 mV) for a longer amount of time than it should. The amount of time varies depending on engine coolant temperature at start-up and average air flow since start-up, but will not exceed 2.5 minutes.

Action Taken When the DTC Sets

    • The PCM will illuminate the malfunction indicator lamp (MIL) during the second consecutive trip in which the diagnostic test has been run and failed.
    • The PCM will store conditions which were present when the DTC set as Freeze Frame/Failure Records data.

Conditions for Clearing the MIL/DTC

    • The PCM will turn OFF the malfunction indicator lamp (MIL) during the third consecutive trip in which the diagnostic has run and passed.
    • The history DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
    • The DTC can be cleared by using a scan tool.

Diagnostic Aids

Inspect for the following conditions:

Many situations may lead to an intermittent condition. Perform each inspection or test as directed.

Important: :  Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.

    • Loose terminal connection
       -  Use a corresponding mating terminal to test for proper tension. Refer to Testing for Intermittent Conditions and Poor Connections , and to Connector Repairs in Wiring Systems for diagnosis and repair.
       -  Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and faulty terminal to wire connection. Refer to Testing for Intermittent Conditions and Poor Connections , and to Connector Repairs in Wiring Systems for diagnosis and repair.
    • Damaged harness--Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the fault. Refer to Wiring Repairs in Wiring Systems for diagnosis and repair.
    •  Inspect the powertrain control module (PCM) and the engine grounds for clean and secure connections. Refer to Wiring Repairs in Wiring Systems for diagnosis and repair.

If the condition is determined to be intermittent, reviewing the Snapshot or Freeze Frame/Failure Records may be useful in determining when the DTC or condition was identified.

Test Description

The numbers below refer to the step numbers on the diagnostic table:

  1. The HO2S should be allowed to cool before performing this test. If the HO2S heater is functioning, the signal voltage will gradually increase or decrease as the sensor element warms. If the heater is not functioning, the HO2S signal will remain near the 450 mv bias voltage.

  2. This step ensures that the ignition feed circuit to the HO2S is not open or shorted. The test lamp should be connected to a good ground, in case the HO2S low or HO2S heater ground circuit is faulty.

  3. This step tests the HO2S heater ground circuit.

  4. This step inspects for an open or shorted HO2S heater element. The heater element resistance will vary according to HO2S temperature (a hot HO2S heater element will measure a much higher resistance than a HO2S heater element at room temperature). It is important to allow the HO2S to cool before measuring HO2S heater element resistance.

Step

Action

Values

Yes

No

1

Did you perform the Powertrain On-Board Diagnostic (OBD) System Check?

--

Go to Step 2

Go to Powertrain On Board Diagnostic (OBD) System Check

2

Important: If engine has just been operating, allow engine to cool for about one half hour before proceeding.

  1. Turn ON the ignition.
  2. With a scan tool, observe the HO2S voltage parameter.

Does HO2S voltage go from bias voltage to more than the first specified value or less than the second specified value?

600 mV

300 mV

Go to Diagnostic Aids

Go to Step 3

3

Inspect the HO2S ignition feed fuse.

Is the fuse open?

--

Go to Step 13

Go to Step 4

4

Important: Use a known good ground. Do not use the HO2S heater ground or low circuit.

  1. Disconnect the HO2S.
  2. Probe the ignition feed circuit (PCM harness side) using a test lamp that is connected to a good ground

Does the test lamp illuminate?

--

Go to Step 5

Go to Step 7

5

Connect the test lamp between the HO2S ignition feed circuit and the HO2S heater ground.

Does test lamp illuminate?

--

Go to Step 6

Go to Step 8

6

  1. Allow the HO2S to cool for at least 10 minutes.
  2. Measure the resistance between the HO2S ignition feed and HO2S heater ground at the pigtail using a digital multimeter.

Does the resistance measure within the specified range?

5-10 ohms

Go to Step 9

Go to Step 12

7

Repair the open HO2S ignition feed circuit. Refer to Wiring Repairs in Wiring Systems.

Did you complete the repair?

--

Go to Step 14

--

8

Repair the open HO2S heater ground circuit. Refer to Wiring Repairs in Wiring Systems.

Did you complete the repair?

--

Go to Step 14

--

9

  1. Inspect for a faulty connection at the HO2S.
  2. If a problem is found, repair as necessary. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 14

Go to Step 10

10

Test the HO2S signal and low circuits for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 14

Go to Step 11

11

Inspect the HO2S signal or low circuits for a faulty connection at the PCM and HO2S. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring System.

Did you find and correct the condition?

--

Go to Step 14

Go to Step 12

12

Replace the HO2S. Refer to Heated Oxygen Sensor Replacement .

Did you complete the repair?

--

Go to Step 14

--

13

Repair the short to ground in HO2S ignition feed circuit and replace faulty fuse. Refer to Wiring Repairs in Wiring Systems.

Did you complete the repair?

--

Go to Step 14

--

14

Important: If engine has just been operating, allow engine to cool for about one half hour before proceeding.

  1. Use the scan tool in order to clear the DTCs.
  2. Turn ON the ignition.
  3. With a scan tool, observe the HO2S voltage for at least 2 minutes.

Does HO2S voltage go from bias voltage to more than the first specified value or less than the second specified value?

600 mV

300 mV

System OK

Go to Step 2