GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Pontiac 🢒 2005 🢒 Grand Am 🢒 Restraints 🢒 SIR 🢒 DTC B0016, B0017, or B0018

Circuit Description

The passenger frontal deployment loop consists of the following components:

    • An inflatable restraint instrument panel (I/P) module
    • The I/P module high circuit
    • The I/P module low circuit

A shorting bar is used on the I/P connector which will short together the I/P high and I/P low control circuits when the connector is disconnected. This will help to prevent unwanted deployment of the inflator module during servicing. When the ignition is turned ON, the inflatable restraint sensing and diagnostic module (SDM) performs continuous diagnostic tests on the deployment loops to check for proper circuit continuity and for shorts to ground or voltage. If a malfunction is detected, a DTC will be stored.

DTC Descriptors

This diagnostic procedure supports the following DTCs:

    • DTC B0016 Passenger Frontal Deployment Loop (Single Stage or Stage 1) Resistance Low
    • DTC B0017 Passenger Frontal Deployment Loop (Single Stage or Stage 1) Open
    • DTC B0018 Passenger Frontal Deployment Loop (Single Stage or Stage 1) Voltage Out of Range

Conditions for Running the DTC

Ignition 1 voltage is within the normal operating voltage range.

Conditions for Setting the DTC
    • DTC B0016 will set when the SDM detects the I/P deployment loop resistance is less than 1.3 ohms for 500 milliseconds.
    • DTC B0017 will set when one of the following conditions occur:
       - The SDM detects the I/P deployment loop resistance is greater than 4.8 ohms for 500 milliseconds.
       - The SDM detects the voltage at I/P high control is less than 2.4 volts and I/P deployment loop resistance is 6 ohms or greater for 500 milliseconds.
    • DTC B0018 will set when one of the following conditions occur:
       - The SDM detects the voltage at I/P high control is greater than 6 volts for 500 milliseconds.
       - The SDM detects the voltage at I/P high control is less than 2.4 volts and I/P deployment loop resistance is less than 6 ohms for 500 milliseconds.

Action Taken When the DTC Sets

The SDM commands ON the AIR BAG indicator via class 2 serial data.

Conditions for Clearing the DTC
    • The condition responsible for setting the DTC no longer exists.
    • You issue a scan tool CLEAR DTCs command.
    • A history DTC will clear once 255 malfunction-free ignition cycles have occurred.

Diagnostic Aids

The following can cause an intermittent condition:

    • A short between the I/P high and I/P low control circuits
    • An open or high resistance in the I/P high or I/P low control circuits
    • A malfunctioning shorting bar on the I/P connector

Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. This step inspects the I/P in-line connector.

    2.

  2. This step tests for a malfunctioning I/P.

    3.

  3. If DTC B0016 is present, test for a short between the I/P high and I/P low control circuits. If DTC B0017 is present, test for an open or high resistance in the I/P high and I/P low control circuits. If DTC B0018 is present, test for a short to ground or voltage in the I/P high and I/P low control circuits.

Step

Action

Yes

No

Schematic Reference: SIR Schematics

Connector End View Reference: SIR Connector End Views

1

Did you perform the Diagnostic System Check - Vehicle?

Go to Step 2

Go to Diagnostic System Check - Vehicle in Vehicle DTC Information

2

  1. Turn OFF the ignition.
  2. Disconnect the instrument panel (I/P) module in-line connector. Refer to Inflatable Restraint Instrument Panel Module Replacement .
  3. Inspect the component and harness sides of the in-line connector for the I/P for damage or corrosion that may cause the malfunction. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Does the connector exhibit any signs of damage or corrosion?

Go to Step 3

Go to Step 4

3
  1. If the I/P connector exhibits any of the above conditions, the module must be replaced. Refer to Inflatable Restraint Instrument Panel Module Replacement .
  2. Replace the harness side of the I/P in-line connector. Refer to Connector Repairs in Wiring Systems.

Did you complete the replacement?

Go to Step 9

--

4

  1. Use the J 38715-A SIR Driver/Passenger Load Tool to connect the harness side of the I/P in-line connector. Use the PASSENGER INFLATOR connector.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, request the SIR DTC display.

Does the scan tool indicate that either DTC B0016, B0017, or B0018 is current?

Go to Step 5

Go to Step 8

5
  1. Turn OFF the ignition.
  2. Remove the J 38715-A .
  3. Disconnect the inflatable restraint sensing and diagnostic module (SDM) connector. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.
  4. Inspect the SDM connector for corrosion or damage. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 9

Go to Step 6

6

  1. If DTC B0016 is present, test the I/P circuits for a short between the high and low circuits.
  2. If DTC B0017 is present, test the I/P high and low circuits for an open or a high resistance.
  3. If DTC B0018 is present, test the I/P high and low circuits for a short to ground or for a short to voltage.
  4. For all the above conditions, refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 9

Go to Step 7

7

Replace the SDM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.

Did you complete the replacement?

Go to Step 9

--

8

Replace the I/P. Refer to Inflatable Restraint Instrument Panel Module Replacement .

Did you complete the replacement?

Go to Step 9

--

9
  1. Reconnect all SIR system components.
  2. Verify that all components, connectors, and connector position assurances (CPAs) are properly mounted.
  3. Use the scan tool in order to clear the DTCs.
  4. Operate the vehicle within the Conditions for Running the DTC, as specified in the supporting text.

Does the DTC reset?

Go to Step 2

System OK