DTC P0562. Pontiac G8 2008

For 1990-2009 cars only

Makes 🢒 Pontiac 🢒 2008 🢒 G8 🢒 Safety and Security 🢒 Supplemental Inflatable Restraints 🢒 DTC P0562

Diagnostic Instructions

•	Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

•	Review Strategy Based Diagnosis for an overview of the diagnostic approach.

•	Diagnostic Procedure Instructions provides an overview of each diagnostic category.

Diagnostic Fault Information

Circuit	Short to Ground	Open/High Resistance	Short to Voltage	Signal Performance
IGN I	P0562	P0562	--	--
Ground	--	P0562	--	--

The engine control module (ECM) monitors the system voltage to ensure that the voltage stays within the proper range. Damage to components, and incorrect data may occur when the voltage is out of range.

Conditions for Running the DTC

•	The vehicle speed is above 8 km/h (5 mph).

•	The system voltage is between 9.5-18 volts.

Conditions for Setting the DTC

The ECM detects a system voltage below 10 volts for 5 seconds.

Action Taken When the DTC Sets

•	The charge indicator turns ON.

•	The driver information center (DIC) displays the SERVICE CHARGING SYSTEM message.

Conditions for Clearing the DTC

DTC P0562 is a C type DTC.

Diagnostic Aids

•	A low voltage DTC set in multiple modules indicates a concern in the charging system.

•	A low voltage value in multiple modules indicates a concern in the charging system.

•	Inspect the ECM ground connection, to verify that it is clean tight.

Reference Information

Schematic Reference

•	Engine Controls Schematics for the 3.6L engine

•	Engine Controls Schematics for the 6.0L engine

Connector End View Reference

Component Connector End Views

Description and Operation

Charging System Description and Operation

Electrical Information Reference

•	Circuit Testing

•	Connector Repairs

•	Testing for Intermittent Conditions and Poor Connections

•	Wiring Repairs

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

Engine running, accessories OFF, measure and record the battery voltage at the battery terminals. The voltage should be between 12.6 and 15.0 V

⇒	If not within the specified range, refer to Charging System Test.

Observe the scan tool ECM Ignition 1 Signal parameter. The reading should be between 12.6 and 15.0 V

Circuit/System Testing

Ignition OFF, disconnect the harness connectors at the ECM.
Ignition OFF, and scan tool disconnected, open and close the driver door, and wait 1 minute. Test for less than 5 Ω between the ground circuit terminals listed below and ground.

•	Terminal 1 X2 (3.6L)

•	Terminal 2 X2 (3.6L)

•	Terminal 4 X2 (3.6L)

•	Terminal 73 X1 (6.0L)

⇒	If greater than the specified range, test the ground circuit for an open/high resistance.

Ignition On, verify that a test lamp illuminates between the IGN/B+ circuit terminals listed below and ground:

•	Terminal 4 X2 (3.6L)

•	Terminal 5 X2 (3.6L)

•	Terminal 6 X2 (3.6L)

•	Terminal 54 X2 (3.6L)

•	Terminal 56 X2 (3.6L)

•	Terminal 19 X1 (6.0L)

•	Terminal 20 X1 (6.0L)

•	Terminal 47 X1 (6.0L)

⇒	If the test lamp does not illuminate , test the IGN/B+ circuit for a short to ground or an open/high resistance.

If all circuits test normal, replace the ECM.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

Control Module References for ECM replacement, setup, and programming