GM Service Manual Online
For 1990-2009 cars only

DTC C0899 EBCM

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of this diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor

DTC C0899 00: Device Voltage Low - EBCM

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

B+

C0899 00

C0899 00

--

--

Ground

--

C0899 00

--

--

Typical Scan Tool Data

Battery Voltage Signal - EBCM

Circuit

Short to Ground

Open

Short to Voltage

Operating Conditions: Ignition ON, engine OFF.

Parameter Normal Value: 12.60 Volts

B+

0.00 Volts

0.00 Volts

12.60 Volts

Circuit/System Description

The electronic brake control module (EBCM) monitors the ignition voltage level available for system operation. A low voltage condition prevents the system from operating properly. If the EBCM detects low system voltage, DTC C0899 00 sets.

Conditions for Running the DTC

The ignition is ON.

Conditions for Setting the DTC

The EBCM detects that the system voltage is less than 9 volts for 100 msec.

Action Taken When the DTC Sets

    • The traction control system (TCS) and vehicle stability enhancement system (VSES) are disabled.
    • The brake indicator turns ON.
    • The ABS indicator turns ON.
    • The stability system off indicator turns ON.
    • The traction control off indicator turns ON.
    • The radio displays the SERVICE TRACTION message.

Conditions for Clearing the DTC

    • The DTC will pass when the EBCM detects that the system voltage is greater than 10 volts.
    • The EBCM automatically clears the history DTC when a current DTC is not detected in 100 consecutive drive cycles.
    • The indicators and radio messages turn OFF when the DTC passes.

Diagnostic Aids

A low voltage DTC in multiple modules indicates a concern in the charging system.

Reference Information

Schematic Reference

Antilock Brake System Schematics

Connector End View Reference

Antilock Brake System Connector End Views

Description and Operation

    •  ABS Description and Operation
    •  Charging System Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

    •  Scan Tool Data List
    •  Scan Tool Data Definitions

Circuit/System Verification

  1. Engine running, accessories OFF, measure and record the voltage at the battery voltage at the battery terminals. The voltage should be between 12.6 and 15.0 volts.
  2. If not within the specified range, refer to Charging System Test .
  3. Observe the scan tool EBCM Battery Voltage Signal parameter. The reading should be between 12.60 and 15.00 volts.

Circuit/System Testing

  1. Ignition OFF, disconnect the harness connector at the EBCM.
  2. Ignition OFF and scan tool disconnected, open and close the driver door, and wait 1 minute. Test for less than 5 ohms between the ground circuit terminals listed below and ground:
  3. • Terminal E
    • Terminal F
    If greater than the specified range, test the ground circuit for an open/high resistance.
  4. Verify that a test lamp illuminates between the B+ circuit terminals listed below and ground:
  5. • Terminal A
    • Terminal B
    If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.
  6. Ignition ON, verify that a test lamp illuminates between the ignition circuit terminal C and ground.
  7. If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance.
  8. If all circuits test normal, replace the EBCM.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

Control Module References for EBCM replacement, setup, and programming.

DTC C0899 PSCM

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor

DTC C0899 03: Device Voltage Low - PSCM

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

Battery Voltage

C0899 03

C0899 03

--

--

Ground

--

C0899 03

--

--

Typical Scan Tool Data

Battery Voltage Signal - PSCM

Circuit

Short to Ground

Open

Short to Voltage

Operating Conditions: Ignition ON, Engine OFF.

Parameter Normal Value: 12.60 Volts

B+

0.00 Volts

0.00 Volts

12.60 Volts

Circuit/System Description

The power steering control module (PSCM) monitors the battery voltage available in order to ensure the power steering system has adequate voltage levels to perform the system functions.

Conditions for Running the DTC

The ignition is ON.

Conditions for Setting the DTC

The power steering system voltage is less than 9 volts for 1 second.

Action Taken When the DTC Sets

    • No steering assist is provided.
    • The driver information center (DIC) displays the POWER STEERING message.

Conditions for Clearing the DTC

    • The condition for the DTC is no longer present.
    • The PSCM automatically clears the history DTC when a current DTC is not detected in 100 consecutive ignition cycles.

Diagnostic Aids

A low voltage DTC in multiple modules indicates a concern in the charging system.

Reference Information

Schematic Reference

Power Steering Schematics

Connector End View Reference

Power Steering Connector End Views

Description and Operation

    •  Power Steering System Description and Operation
    •  Charging System Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

    •  Scan Tool Data List
    •  Scan Tool Data Definitions

Circuit/System Verification

  1. Engine running, accessories OFF, measure and record the voltage at the battery voltage at the battery terminals. The voltage should be between 12.6 and 15.0 volts.
  2. If not within the specified range, refer to Charging System Test .
  3. Observe the scan tool PSCM Battery Voltage Signal parameter. The reading should be between 12.6 and 15.0 volts.

Circuit/System Testing

  1. Ignition OFF, disconnect the harness connector at the PSCM.
  2. Ignition OFF and scan tool disconnected, open and close the driver door, and wait 1 minute. Test for less than 5 ohms between the ground circuit terminal A C1 and ground.
  3. If greater than the specified range, test the ground circuit for an open/high resistance.
  4. Verify that a test lamp illuminates between the B+ circuit terminal B C1 and ground.
  5. If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.
  6. Ignition ON, verify that a test lamp illuminates between the ignition circuit terminal 8 C2 and ground.
  7. If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance.
  8. If all circuits test normal, replace the PSCM.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

Control Module References for PSCM replacement, setup and programming.