GM Service Manual Online
For 1990-2009 cars only

Test Description

The numbers below refer to the step numbers in the diagnostic table.

  1. There are 2 blower motor supply voltage circuits at the blower motor relay. Probe the circuit that is connected to the blower motor resistor assembly.

  2. There are 2 ignition 3 voltage circuits at the HVAC control module. Probe the circuit that is the supply voltage to the blower motor switch.

Step

Action

Yes

No

Schematic Reference: HVAC Schematics

Connector End View Reference: HVAC Connector End Views

DEFINITION: The blower motor is inoperative in all speed positions.

1

Did you perform the Diagnostic System Check - Vehicle?

Go to Step 2

Go to Diagnostic System Check - Vehicle

2

  1. Turn ON the ignition, with the engine OFF.
  2. Place the mode switch in the vent position.
  3. Place the blower motor switch in each speed position.

Does the blower motor operate in any speed position?

Go to Blower Motor Malfunction

Go to Step 3

3

  1. Turn OFF the ignition.
  2. Disconnect the blower motor.
  3. Turn ON the ignition, with the engine OFF.
  4. Connect a test lamp between the blower motor supply voltage circuit of the blower motor and a good ground.
  5. Place the blower motor switch in the minimum speed position.

Does the test lamp illuminate?

Go to Step 4

Go to Step 5

4

Test the ground circuit of the blower motor for an open or high resistance. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

Go to Step 15

Go to Step 9

5

Test the blower motor supply voltage circuit between the blower motor and the blower motor relay for the following:

    • An open
    • A high resistance
    • A short to ground

Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

Go to Step 15

Go to Step 6

6

  1. Turn OFF the ignition.
  2. Disconnect the blower motor relay.
  3. Turn ON the ignition, with the engine OFF.
  4. Place the blower motor switch in the minimum speed position.
  5. Probe the blower motor supply voltage circuit with a test lamp that is connected to a good ground.

Does the test lamp illuminate?

Go to Step 8

Go to Step 7

7

  1. Turn OFF the ignition.
  2. Disconnect the HVAC control module.
  3. Turn ON the ignition, with the engine OFF.
  4. Connect a test lamp between the ignition 3 voltage circuit of the HVAC control assembly and a good ground.

Does the test lamp illuminate?

Go to Step 10

Go to Step 11

8

Inspect for poor connections at the harness connector of the blower motor relay. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

Go to Step 15

Go to Step 12

9

Inspect for poor connections at the harness connector of the blower motor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

Go to Step 15

Go to Step 13

10

Inspect for poor connections at the harness connector of the HVAC control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

Go to Step 15

Go to Step 14

11

Repair the ignition 3 voltage circuit of the HVAC control module. Refer to Wiring Repairs .

Did you complete the repair?

Go to Step 15

--

12

Replace the blower motor relay.

Did you complete the replacement?

Go to Step 15

--

13

Replace the blower motor. Refer to Blower Motor Replacement .

Did you complete the replacement?

Go to Step 15

--

14

Replace the HVAC control module. Refer to Control Module References for replacement, setup, and programming.

Did you complete the replacement?

Go to Step 15

--

15

Operate the system in order to verify the repair.

Did you correct the condition?

System OK

Go to Step 3