GM Service Manual Online
For 1990-2009 cars only

Special Tools

    • EN 46105 Camshaft Locking Tool
    • EN 46109 Guide Pin Set
    • EN 46111 Crankshaft Rotational Socket

Removal Procedure

  1. Remove the lower intake manifold. Refer to Lower Intake Manifold Replacement.
  2. Remove the camshaft covers. Refer to Camshaft Cover Replacement - Left Side and Camshaft Cover Replacement - Right Side.
  3. Drain the engine coolant. Refer to Cooling System Draining and Filling.
  4. Remove the drive belt tensioner. Refer to Drive Belt Tensioner Replacement.
  5. Remove the water pump. Refer to Water Pump Replacement.
  6. Remove the power steering pump and position aside. Refer to Power Steering Pump Replacement.
  7. Remove the camshaft position sensors. Refer to Camshaft Position Sensor Replacement - Bank 2 (Left Side) Exhaust , Camshaft Position Sensor Replacement - Bank 2 (Left Side) Intake , Camshaft Position Sensor Replacement - Bank 1 (Right Side) Exhaust and Camshaft Position Sensor Replacement - Bank 1 (Right Side) Intake.
  8. Remove the camshaft position actuator solenoid valves from the front cover. Refer to Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 1 (Right Side) Intake , Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 1 (Right Side) Exhaust , Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 2 (Left Side) Intake , and Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 2 (Left Side) Exhaust.
  9. Remove the generate. Refer to Generator Replacement.
  10. Remove the water outlet housing. Refer to Engine Coolant Thermostat Housing Replacement.
  11. Remove the crankshaft balancer. Refer to Crankshaft Balancer Replacement Clean front cover of components first before installing a support fixture.
  12. Insert a block of hard wood between the frame and engine before using support fixture. Lower engine onto block of wood. Remove lift hook and strut mount bracket from the front cover.

  13. Object Number: 1412164  Size: SH
  14. Remove the engine front cover bolts.

  15. Object Number: 1412166  Size: SH
  16. Loosely install a 10 x 1.5 mm bolt in the "jackscrew" hole (1).
  17. Using the pry points (2) located at the edge of the front cover and the "jackscrew", shear the RTV sealant.

  18. Object Number: 1586271  Size: SH
  19. Remove the engine front cover.

  20. Object Number: 1592695  Size: SH
  21. Using the EN 46111 , rotate the crankshaft until the left cylinder head camshafts align with the EN 46105-2 and the right cylinder head camshafts align with the EN 46105-1.

  22. Object Number: 946124  Size: SH
  23. Install the EN 46105-1 to the right camshafts.

  24. Object Number: 1306428  Size: SH
  25. Install the EN 46105-2 to the left camshafts.

Installation Procedure


    Object Number: 1586270  Size: SH
  1. Install the 8 mm (0.315 in) guide from the EN 46109 into the cylinder block positions as shown.

  2. Object Number: 1211002  Size: SH
  3. Install the engine front cover to cylinder block seal.

  4. Object Number: 1408422  Size: SH
  5. Place a 3 mm (0.118 in) bead of RTV sealant, GM P/N 12378521 (Canadian P/N 88901148) or equivalent, on the engine front cover as shown (1).

  6. Object Number: 1586271  Size: SH
  7. Place the engine front cover onto the EN 46109 and slide into position.
  8. Remove the EN 46109 from the cylinder block.

  9. Object Number: 1412164  Size: SH
  10. Hand start all the front cover bolts.
  11. Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 1545382  Size: SH
  12. Tighten the engine front cover bolts in the sequence shown.
  13. Tighten
    Tighten the engine front cover bolts in sequence to 23 N·m (17 lb ft).

  14. Install the engine oil pan. Refer to Oil Pan Replacement.
  15. Install the engine coolant thermostat housing. Refer to Engine Coolant Thermostat Housing Replacement.
  16. Reinstall the engine support fixture. Refer to Engine Support Fixture.
  17. Remove the engine mount bracket. Refer to Engine Mount Bracket Replacement - Right Side.
  18. Install the camshaft position actuator solenoid valves to the front cover. Refer to Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 1 (Right Side) Intake , Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 1 (Right Side) Exhaust , Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 2 (Left Side) Intake , and Camshaft Position Actuator Solenoid Valve Solenoid Replacement - Bank 2 (Left Side) Exhaust.
  19. Install the camshaft position sensors. Refer to Camshaft Position Sensor Replacement - Bank 2 (Left Side) Exhaust , Camshaft Position Sensor Replacement - Bank 2 (Left Side) Intake , Camshaft Position Sensor Replacement - Bank 1 (Right Side) Exhaust and Camshaft Position Sensor Replacement - Bank 1 (Right Side) Intake.
  20. Install the crankshaft balancer. Refer to Crankshaft Balancer Replacement.
  21. Install the power steering pump and position aside. Refer to Power Steering Pump Replacement.
  22. Install the water pump. Refer to Water Pump Replacement.
  23. Install the drive belt tensioner. Refer to Drive Belt Tensioner Replacement.
  24. Install the camshaft covers. Refer to Camshaft Cover Replacement - Left Side and Camshaft Cover Replacement - Right Side.
  25. Install the lower intake manifold. Refer to Lower Intake Manifold Replacement.
  26. Refill the engine coolant. Refer to Cooling System Draining and Filling.