GM Service Manual Online
For 1990-2009 cars only

Fuel Tank Replacement RPO NT7

Removal Procedure

Caution: Refer to Gasoline/Gasoline Vapors Caution in the Preface section.


    Object Number: 1656956  Size: SH
  1. Relieve the fuel system pressure. Refer to Fuel Pressure Relief .
  2. Drain the fuel tank. Refer to Fuel Tank Draining .
  3. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .
  4. Disconnect the fuel pump module fuel feed (2) and return (1) line quick connect fittings from the fuel filter. Refer to Plastic Collar Quick Connect Fitting Service .
  5. Cap or plug the fuel filter feed and return line fittings in order to prevent fuel loss and/or system contamination.
  6. Cap or plug the fuel pump module feed and return lines in order to prevent fuel loss and/or system contamination.

  7. Object Number: 1656958  Size: SH
  8. Disconnect the fuel tank evaporative emission (EVAP) line quick connect fittings (2, 3) from the EVAP canister. Refer to Plastic Collar Quick Connect Fitting Service .
  9. Cap or plug the EVAP lines and canister fittings in order to prevent system contamination.

  10. Object Number: 1656960  Size: SH
  11. Disconnect the fuel tank vent line quick connect fitting (2) from the fill pipe recirculation line. Refer to Plastic Collar Quick Connect Fitting Service .
  12. Loosen the fuel fill hose clamp (3) at the fuel tank.
  13. Remove the fuel fill hose from the fuel tank.
  14. Cap or plug the fuel tank opening and vent line in order to prevent fuel loss and/or system contamination.

  15. Object Number: 1656962  Size: SH
  16. Disconnect the fuel tank harness electrical connectors (1 and 3) from the body harness pass thru connector (2).

  17. Object Number: 1652166  Size: SH
  18. Disconnect the fuel tank harness electrical connector (1) from the fuel tank pressure sensor.
  19. Disconnect the fuel tank harness electrical connector (2) from the EVAP canister vent solenoid valve.
  20. Remove the harness retainers from the underbody.

  21. Object Number: 1651437  Size: SH
  22. Release the exhaust muffler assembly insulators from the underbody hangers and slowly lower the exhaust, allowing it to rest on the rear axle beam.

  23. Object Number: 1656964  Size: SH
  24. Use a suitable jack to support the fuel tank during the fuel tank strap and tank removal.
  25. Remove the left (L) fuel tank strap bolts and strap.
  26. Remove the right (R) fuel tank strap bolts and strap.
  27. In order to clear the exhaust muffler assembly, slowly lower the right side of the fuel tank. Use care when feeding the fuel, EVAP lines, and electrical harness around rear axle.
  28. Once the fuel tank is clear of the right frame rail, remove the fuel tank down and toward the right side of the vehicle.
  29. If the fuel tank is be replaced, remove the fuel pump module. Refer to Fuel Pump Module Replacement .

Installation Procedure


    Object Number: 1656964  Size: SH
  1. If the fuel tank was replaced, install the fuel pump module. Refer to Fuel Pump Module Replacement .
  2. Use a suitable jack to support the fuel tank during the fuel tank and strap installation.
  3. Install the left side of the fuel tank over the exhaust muffler assembly.
  4. Raise the right side of the fuel tank into position inboard of the right frame rail. Use care when feeding the fuel, EVAP lines, and electrical harness over the rear axle.
  5. Install the right (R) fuel tank strap and bolts.
  6. Install the left (L) fuel tank strap and bolts.
  7. Notice: Refer to Fastener Notice in the Preface section.

  8. Tighten the fuel tank strap bolts.
  9. Tighten
    Tighten the bolts to 25 N·m (18 lb ft).


    Object Number: 1651437  Size: SH
  10. Raise the exhaust muffler assembly into position and install the insulators to the underbody hanger.

  11. Object Number: 1652166  Size: SH
  12. Connect the fuel tank harness electrical connector (1) to the fuel tank pressure sensor.
  13. Connect the fuel tank harness electrical connector (2) to the EVAP canister vent solenoid valve.
  14. Install the harness retainers to the underbody.

  15. Object Number: 1656962  Size: SH
  16. Connect the fuel tank harness electrical connectors (1 and 3) to the body harness pass thru connector (2).

  17. Object Number: 1656960  Size: SH
  18. Remove the cap or plug from the fuel tank and vent line openings.
  19. Connect the fuel fill hose to the fuel tank. Align the "D" notch on the fill hose (1) with the "D" notch on the fuel tank (1).
  20. Notice: Refer to Component Fastener Tightening Notice in the Preface section.

  21. Tighten the fuel fill hose clamp (3).
  22. Tighten
    Tighten the clamp to 4.5 N·m (40 lb in).

  23. Connect the fuel tank vent line quick connect fitting (2) to the fill pipe recirculation line. Refer to Plastic Collar Quick Connect Fitting Service .

  24. Object Number: 1656958  Size: SH
  25. Remove the caps or plugs from the EVAP lines.
  26. Connect the fuel tank EVAP line quick connect fittings (2, 3) to the EVAP canister. Refer to Plastic Collar Quick Connect Fitting Service .

  27. Object Number: 1656956  Size: SH
  28. Remove the caps or plugs from the fuel pump module fuel feed and return lines.
  29. Remove the caps or plugs from the fuel filter feed and return line fittings.
  30. Connect the fuel pump module fuel feed (2) and return (1) line quick connect fittings to the fuel filter. Refer to Plastic Collar Quick Connect Fitting Service .
  31. Lower the vehicle.
  32. Refill the fuel tank.
  33. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
  34. Inspect for fuel leaks using the following procedure:
  35. 25.1. Turn ON the ignition, with the engine OFF for 2 seconds.
    25.2. Turn OFF the ignition for 10 seconds.
    25.3. Turn ON the ignition, with the engine OFF.
    25.4. Inspect for fuel leaks.

Fuel Tank Replacement RPO NU6

Removal Procedure

Caution: Refer to Gasoline/Gasoline Vapors Caution in the Preface section.


    Object Number: 1651435  Size: SH
  1. Relieve the fuel system pressure. Refer to Fuel Pressure Relief .
  2. Drain the fuel tank. Refer to Fuel Tank Draining .
  3. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .
  4. Disconnect the fuel tank line quick connect fitting from the fuel feed line. Refer to Plastic Collar Quick Connect Fitting Service .
  5. Cap or plug the fuel feed line and the fuel tank line in order to prevent fuel loss and/or system contamination.
  6. Disconnect the fuel tank evaporative emission (EVAP) line quick connect fitting (3) from the EVAP canister. Refer to Plastic Collar Quick Connect Fitting Service .
  7. Disconnect the fuel fill pipe fresh air line quick connect fitting (2) from the EVAP canister. Refer to Plastic Collar Quick Connect Fitting Service .
  8. Cap or plug the EVAP/fresh air lines and canister fittings in order to prevent system contamination.

  9. Object Number: 1752397  Size: SH
  10. Disconnect the fuel tank vent line quick connect fitting (1) from the fill pipe recirculation line. Refer to Plastic Collar Quick Connect Fitting Service .
  11. Loosen the fuel fill hose clamp (2) at the fuel tank.
  12. Remove the fuel fill hose from the fuel tank.
  13. Cap or plug the fuel tank opening and vent line in order to prevent fuel loss and/or system contamination.

  14. Object Number: 1656962  Size: SH
  15. Disconnect the fuel tank harness electrical connectors (1 and 3) from the body harness pass thru connector (2).

  16. Object Number: 1652166  Size: SH
  17. Disconnect the fuel tank harness electrical connector (1) from the fuel tank pressure sensor.
  18. Disconnect the fuel tank harness electrical connector (2) from the EVAP canister vent solenoid valve.
  19. Remove the harness retainers from the underbody.

  20. Object Number: 1651437  Size: SH
  21. Release the exhaust muffler assembly insulators from the underbody hangers and slowly lower the exhaust, allowing it to rest on the rear axle beam.

  22. Object Number: 1752249  Size: SH
  23. Remove the fuel tank harness clips from the underbody.
  24. Use a suitable jack to support the fuel tank during the fuel tank strap and tank removal.
  25. Remove the left (L) fuel tank strap bolts and strap.
  26. Remove the right (R) fuel tank strap bolts and strap.
  27. In order to clear the exhaust muffler assembly, slowly lower the right side of the fuel tank. Use care when feeding the fuel, EVAP lines, and electrical harness around rear axle.
  28. Once the fuel tank is clear of the right frame rail, remove the fuel tank down and toward the right side of the vehicle.
  29. If the fuel tank is be replaced, remove the following components:
  30. • Fuel level sensor. Refer to Fuel Level Sensor Replacement.
    • Fuel pump. Refer to Fuel Pump Replacement.
    • Fuel pump fuel reservoir pump fuel strainer. Refer to Fuel Pump Fuel Reservoir Pump Fuel Strainer Orifice Replacement.

Installation Procedure


    Object Number: 1752249  Size: SH
  1. If the fuel tank was replaced, install the following components:
  2. • Fuel pump fuel reservoir pump fuel strainer. Refer to Fuel Pump Fuel Reservoir Pump Fuel Strainer Orifice Replacement.
    • Fuel level sensor. Refer to Fuel Level Sensor Replacement.
    • Fuel pump. Refer to Fuel Pump Replacement.
  3. Use a suitable jack to support the fuel tank during the fuel tank and strap installation.
  4. Install the left side of the fuel tank over the exhaust muffler assembly.
  5. Raise the right side of the fuel tank into position inboard of the right frame rail. Use care when feeding the fuel, EVAP lines, and electrical harness over the rear axle.
  6. Install the right (R) fuel tank strap and bolts.
  7. Install the left (L) fuel tank strap and bolts.
  8. Notice: Refer to Fastener Notice in the Preface section.

  9. Tighten the fuel tank strap bolts.
  10. Tighten
    Tighten the bolts to 25 N·m (18 lb ft).

  11. Install the fuel tank harness clips to the underbody.

  12. Object Number: 1651437  Size: SH
  13. Raise the exhaust muffler assembly into position and install the insulators to the underbody hanger.

  14. Object Number: 1652166  Size: SH
  15. Connect the fuel tank harness electrical connector (1) to the fuel tank pressure sensor.
  16. Connect the fuel tank harness electrical connector (2) to the EVAP canister vent solenoid valve.
  17. Install the harness retainers to the underbody.

  18. Object Number: 1656962  Size: SH
  19. Connect the fuel tank harness electrical connectors (1 and 3) to the body harness pass thru connector (2).

  20. Object Number: 1752397  Size: SH
  21. Remove the cap or plug from the fuel tank and vent line openings.
  22. Connect the fuel fill hose to the fuel tank.
  23. Notice: Refer to Component Fastener Tightening Notice in the Preface section.

  24. Tighten the fuel fill hose clamp (2).
  25. Tighten
    Tighten the clamp to 4.5 N·m (40 lb in).

  26. Connect the fuel tank vent line quick connect fitting (1) to the fill pipe recirculation line. Refer to Plastic Collar Quick Connect Fitting Service .

  27. Object Number: 1651435  Size: SH
  28. Remove the caps or plug from the EVAP/fresh air lines and canister fittings.
  29. Connect the fuel fill pipe fresh air line quick connect fitting (2) to the EVAP canister. Refer to Plastic Collar Quick Connect Fitting Service .
  30. Connect the fuel tank EVAP line quick connect fitting (3) to the EVAP canister. Refer to Plastic Collar Quick Connect Fitting Service .
  31. Remove the cap or plug from the fuel feed line and the fuel tank line.
  32. Connect the fuel tank line quick connect fitting to the fuel feed line. Refer to Plastic Collar Quick Connect Fitting Service .
  33. Lower the vehicle.
  34. Refill the fuel tank.
  35. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
  36. Inspect for fuel leaks using the following procedure:
  37. 26.1. Turn ON the ignition, with the engine OFF for 2 seconds.
    26.2. Turn OFF the ignition for 10 seconds.
    26.3. Turn ON the ignition, with the engine OFF.
    26.4. Inspect for fuel leaks.