GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC P0201: Injector 1 Control Circuit

DTC P0202: Injector 2 Control Circuit

DTC P0203: Injector 3 Control Circuit

DTC P0204: Injector 4 Control Circuit

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

Ignition 1 Voltage - Fuse to Splice

¹

²

--

--

Ignition 1 Voltage - Splice to Injector

¹

P0201, P0202, P0203, or P0204

--

--

Fuel Injector 1 Control

P0201

P0201

P0201

--

Fuel Injector 2 Control

P0202

P0202

P0202

--

Fuel Injector 3 Control

P0203

P0203

P0203

--

Fuel Injector 4 Control

P0204

P0204

P0204

--

¹Open fuse, cranks no start

²Cranks no start

Circuit/System Description

The control module enables the appropriate fuel injector pulse for each cylinder. Ignition voltage is supplied to the fuel injectors. The control module controls each fuel injector by grounding the control circuit via a solid state device called a driver. The control module monitors the status of each driver. If the control module detects an incorrect voltage for the commanded state of the driver, a fuel injector control circuit DTC sets.

Conditions for Running the DTC

    • The engine is running.
    • The ignition voltage is between 11-18 volts for more than 1 second.
    • DTCs P0201-P0204 runs continuously when the above conditions are met.

Conditions for Setting the DTC

    • The control module detects an incorrect voltage on the fuel injector control circuit.
    • The above condition is met for more than 6 seconds.

Action Taken When the DTC Sets

DTCs P0201, P0202, P0203, P0204 are Type B DTCs.

Conditions for Clearing the DTC

DTCs P0201, P0202, P0203, P0204 are Type B DTCs.

Diagnostic Aids

Performing the Fuel Injector Diagnosis may help isolate an intermittent condition. Refer to Fuel Injector Diagnosis .

Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

    •  Engine Control Module Connector End Views
    •  Engine Controls Connector End Views

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

    •  Scan Tool Data List
    •  Scan Tool Data Definitions
    •  Scan Tool Output Controls

Special Tools Required

J 44603 Injector Test Lamp

Circuit/System Testing

  1. Ignition OFF, disconnect the harness connector at the appropriate fuel injector.
  2. Ignition ON, verify that a test lamp illuminates between the ignition circuit terminal 1 or A and ground.
  3. If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit tests normal and the ignition circuit fuse is open, test or replace the fuel injector.
  4. Ignition OFF, connect a J 44603 between the control circuit terminal 2 or B and the ignition circuit terminal 1 or A of the appropriate fuel injector.
  5. Engine running, the test lamp should flash.
  6. If the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the engine control module (ECM).
    If the test lamp is always OFF, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the ECM.
  7. If all circuits test normal, test or replace the fuel injector.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Control Module References for ECM replacement, setup, and programming
    •  Fuel Injector Replacement