Steering Gear Replacement V6

1. Place drain pan(s) under vehicle under steering gear and pump.
2. Raise and suitably support vehicle. Refer to Lifting and Jacking the Vehicle in General Information.



3. Remove power steering gear inlet (3) and outlet (2) hoses from steering gear (1).
4. Lower vehicle.
5. Remove the serpentine belt.
6. Remove the power steering pump pulley. Refer to Power Steering Pump Pulley Replacement .



7. Remove inlet hose fitting (3) from pump (1).
8. Remove outlet hose from reservoir.

Important: Inlet and outlet hoses must be oriented so as adequate clearance is maintained between both hoses and surrounding components to prevent chafing. Use minimum clearance of 12 mm (0.47 in). The outlet hose must not be twisted during installation. Do not bend or distort inlet and outlet hoses to make installation easier. Failure to follow these procedures could result in component damage.




1. Install outlet hose to reservoir.
2. Install inlet hose fitting (3) to pump (1).
3. Install the power steering pump pulley. Refer to Power Steering Pump Pulley Replacement .
4. Install the serpentine belt.
5. Raise and suitably support vehicle. Refer to Lifting and Jacking the Vehicle in General Information.



6. Install inlet and outlet hoses (2, 3) to steering gear (1).

Tighten

•	Tighten the inlet hose (3) to 28 N·m (21 lb ft).

•	Tighten the outlet hose (2) to 28 N·m (21 lb ft).

7. Lower vehicle.
8. Remove drain pan.
9. Refill and bleed power steering system. Refer to Power Steering System Bleeding .

Steering Gear Replacement V8

1. Remove the air intake resonator.
2. Remove the serpentine belt.
3. Support the engine with a hydraulic jack.
4. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
5. Remove the tires and wheels. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
6. Place a drain pan under the steering gear (5).
7. Disconnect the steering gear outer tie rods.
8. Remove the generator.
9. Remove the left-side engine mount through bolt.
10. Lower the vehicle.
11. Raise the engine with the hydraulic jack.
12. Disconnect the following hoses from the steering gear (5):

•	The power steering gear inlet hose

•	The power steering gear outlet hose

13. Remove the steering gear flexible coupling from the steering gear (5). Refer to Intermediate Steering Shaft Replacement in Steering Wheel and Column.
14. Remove the nuts (4) and bolts/screws (1).
15. Remove the steering gear (5).

1. Position the steering gear (5) to the crossmember (2).
2. Adjust the steering gear (5).

Ensure that the steering aligns as straight as possible with the steering gear coupling shaft.

3. Hand start the bolts (1) and nut (4).
4. Position the back-up wrench to the nuts (4).

Tighten
Tighten the bolts to 85 N·m (63 lb ft).

5. Install the steering gear flexible coupling to the steering gear. Refer to Intermediate Steering Shaft Replacement in Steering Wheel and Column.

Tighten
Tighten the bolts to 47 N·m (35 lb ft).

6. Connect the following hoses to the steering gear (5).

Tighten

1. Tighten the inlet hose to 28 N·m (21 lb ft).
2. Tighten the outlet hose to 28 N·m (21 lb ft).
7. Lower the vehicle. Allow the vehicle to stay slightly above the ground while the tires and wheels are not installed.
8. Lower the engine with the hydraulic jack.
9. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle .
10. Install the left side engine mount through-bolt.
11. Install the generator.
12. Connect the steering gear outer tie rods to the steering knuckles.
13. Install the tire and wheels. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
14. Lower the vehicle.
15. Remove the hydraulic jack supporting the engine.
16. Install the serpentine belt.
17. Install the air intake resonator.
18. Refill and bleed the power steering system. Refer to Power Steering System Bleeding .