GM Service Manual Online
For 1990-2009 cars only

Engine Cranks But Does Not Run without Supercharger

Circuit Description

The Engine Cranks but Does Not Run diagnostic table is an organized approach to identifying a condition that causes an engine not to start. The Engine Cranks but Does Not Run diagnostic table directs the service technician to the appropriate system diagnosis. The Engine Cranks but Does Not Run diagnostic table assumes the following:

    • The battery is completely charged. Refer to Battery Inspection/Test in Engine Electrical.
    • The engine cranking speed is acceptable. Refer to Engine Cranks Slowly in Engine Electrical.
    • There is adequate fuel in the fuel tank.

Step

Action

Values

Yes

No

Schematic Reference: Engine Controls Schematics

Connector End View Reference: Engine Controls Connector End Views or Powertrain Control Module Connector End Views

1

Did you perform the Diagnostic System Check-Engine Controls?

--

Go to Step 2

Go to Diagnostic System Check - Engine Controls

2

  1. Turn ON the ignition, with the engine OFF.
  2. Observe the DTC information with a scan tool.

Is DTC P0101, P0123, P0230, P0336, P0341, P0601, P0602, P1626, P1629, P1631 or P1683 set?

--

Go to Diagnostic Trouble Code (DTC) List

Go to Step 3

3

Observe the engine speed parameter with a scan tool, while the engine is cranking.

Does the engine speed parameter display cranking RPM?

--

Go to Step 4

Go to Electronic Ignition (EI) System Diagnosis

4

Command the fuel pump relay ON with a scan tool.

Does the fuel pump turn ON?

--

Go to Step 5

Go to Fuel Pump Electrical Circuit Diagnosis

5

  1. Turn OFF the ignition.
  2. Disconnect a spark plug wire.
  3. Install the J 26792 Spark Tester to the spark plug wire.
  4. Attempt to start the engine.

Does the spark tester spark?

--

Go to Step 6

Go to Electronic Ignition (EI) System Diagnosis

6

  1. Turn OFF the ignition.
  2. Disconnect a fuel injector connector.
  3. Install the J 34730-405 Fuel Injector Test Lamp (L36) to the fuel injector connector.
  4. Attempt to start the engine.

Does the test lamp blink while the engine is cranking?

--

Go to Step 7

Go to DTC P0341

7

  1. Turn OFF the ignition.
  2. Install the J 34730-1A Fuel Pressure Gage. Refer to Fuel Pressure Gage Installation and Removal .
  3. Turn ON the ignition, with the engine OFF.
  4. Command the fuel pump relay ON with a scan tool.

Is the fuel pressure within the specified range while the fuel pump is operating?

364-405 kPa (53-59 psi)

Go to Step 8

Go to Fuel System Diagnosis

8

Inspect for the following conditions:

    • Collapsed air intake duct
    • Restricted air filter element--Refer to Air Cleaner Element Replacement .
    • Fouled spark plugs--Refer to Spark Plug Inspection . If the spark plugs are fouled, determine what caused the condition.
    • Engine mechanical condition (worn timing chain and gears, low compression, etc.)--Refer to Symptoms - Engine Mechanical in Engine Mechanical 3.8L.
    • Restricted exhaust system--Refer to Restricted Exhaust in Engine Exhaust.
    • Faulty engine coolant temperature (ECT) sensor
    • Faulty manifold absolute pressure (MAP) sensor--Refer to Manifold Absolute Pressure Sensor Diagnosis .
    • Stuck throttle position (TP) sensor--Refer to DTC P0121 .

Did you complete the action?

--

Go to Step 9

--

9

  1. Clear the DTCs with a scan tool.
  2. Attempt to start the engine.

Does the engine start and continue to operate?

--

Go to Step 10

Go to Step 2

10

  1. Idle the engine.
  2. Allow the engine to reach operating temperature.
  3. Observe the DTC information with a scan tool.

Are any DTCs displayed?

--

Go to Diagnostic Trouble Code (DTC) List

System OK