GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Pontiac 🢒 2000 🢒 Bonneville 🢒 Body and Accessories 🢒 Instrument Panel, Gauges, and Console 🢒 Powertrain On Board Diagnostic (OBD) System Check

Refer to Engine Controls Schematic Engine Controls Schematics .

Circuit Description

The Powertrain On-Board Diagnostic System Check must be the starting point for any driveability complaint diagnosis. Before using this procedure, you should perform a careful visual and physical check of the PCM and the engine grounds for being clean and tight. The Powertrain On-Board Diagnostic System Check is an organized approach to identifying a problem created by an electronic engine control system malfunction.

Diagnostic Aids

An intermittent may be caused by a poor connection, rubbed-through wire insulation, or a wire broken inside the insulation. Check for poor connections or a damaged harness. Inspect the PCM harness and connectors for improper mating, broken locks, improperly formed or damaged terminals, poor terminal-to-wire connection, and a damaged harness.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. The malfunction indicator lamp (MIL) should be ON steady with the key ON and the engine OFF. If not, the No Malfunction Indicator Lamp table should be used to isolate the malfunction.

  2. This test ensures that the PCM is capable of transmitting Class 2 serial data to the DLC and that the Class 2 data circuit is not open or shorted. If a problem is encountered and a malfunctioning scan tool is suspected, try the scan tool on another vehicle to verify operation. If a DLC problem exists, the DLC diagnosis table should be used to diagnose the condition.

    3.

  3. If the engine will not start, the Engine Cranks But Will Not Run table should be used to diagnose the condition.

    4.

  4. The scan tool may display DTCs which are diagnosed in Automatic Transaxle 4T65-E . Go to Powertrain Control Module Diagnosis for a complete list of DTCs supported by this vehicle application. If multiple DTCs are stored, diagnose each DTC according to the following priority:

    5. 1. PCM malfunction DTCs P0601, P0602.
    2. System voltage DTCs P0560, P1635, P1639.
    3. Component level DTCs (switches, sensor range/performance, sensor high voltage, sensor low voltage, ODMs, etc.).
    4. System level DTCs (fuel trim, misfire, EGR flow, TWC system, EVAP system, idle control system, HO2S response or HO2S transition time ratio).

  5. A scan tool parameter which is not within the typical range may help to isolate the area which is causing the problem.

Powertrain On--Board Diagnostic System Check

Step

Action

Values

Yes

No

1

Important:: 

   • Check for applicable service bulletins before proceeding with diagnosis.
   • Do not turn the ignition OFF when performing this diagnostic procedure.
   • Do not perform this test if no driveablity condition exists.
   • Do not clear DTCs unless the diagnostic instructs you to.

  1. Turn ON the ignition switch.
  2. Observe the malfunction indicator lamp (MIL).

Is the MIL ON?

--

Go to Step 2

Go to Malfunction Indicator Lamp (MIL) Inoperative

2

  1. Connect a scan tool.
  2. Attempt to display the PCM data with the scan tool.

Does the scan tool display the PCM data?

--

Go to Step 3

Go to Data Link Connector Diagnosis

3

Attempt to start the engine.

Does the engine start and continue to run?

--

Go to Step 4

Go to Engine Cranks but Does Not Run

4

  1. Use the scan tool in order to display DTC Info.
  2. If any DTCs are stored, save the Freeze Frame and Failure Record information.

Are there any DTCs stored?

--

Go to Powertrain Control Module Diagnosis

Go to Step 5

5

Compare the PCM data values displayed on the scan tool to the Scan Tool Data Definitions .

Are the displayed values normal or close to the typical values?

--

System OK

Go to Diagnostic Trouble Code (DTC) List/Type