Too Cold in Vehicle. Pontiac Aztek

For 1990-2009 cars only

Makes 🢒 Pontiac 🢒 2001 🢒 Aztek - FWD 🢒 HVAC 🢒 HVAC Systems - Manual 🢒 Too Cold in Vehicle

Test Description

The numbers below refer to the step numbers on the diagnostic table.

The voltage will vary between 0-12 volts during normal operation. The HVAC control module connector must be connected during this step.

Step

Action

Values

Yes

Schematic Reference: HVAC Schematics

DEFINITION: The temperature cannot be adjusted, or the heating is insufficient.

Important: Both left (driver) and right (passenger) air temperature control concerns are diagnosed in this table.

Did you perform the HVAC Diagnostic System Check?

Go to Step 2

Go to Diagnostic System Check - HVAC Systems - Manual

Turn ON the ignition, with the engine OFF.
Place the blower motor switch in each speed position.

Does the blower motor operate at all?

Go to Step 3

Go to Blower Motor Inoperative

Does the blower motor operate when the blower motor switch is in each speed position?

Go to Step 4

Go to Blower Motor Malfunction

Except for the blower motor speed, are all of the functions of the HVAC control module inoperative?

Go to Step 13

Go to Step 5

Inspect the cooling system for the following:

A low coolant level
A loose or worn accessory drive belt
A leaking radiator hose or heater hoses
A kinked radiator hose or heater hoses
A missing radiator cap pressure seal
A leaking radiator cap

Did you find and correct the condition?

Go to Step 22

Go to Step 6

Start the engine.
Place the blower switch in the OFF position.
Place the A/C request switch in the OFF position.

Does the A/C compressor operate?

Go to HVAC Compressor Clutch Does Not Disengage

Go to Step 7

Observe the air temperature actuator drive shaft.
Adjust the air temperature switch.

Does the air temperature actuator drive shaft rotate?

Go to Step 8

Go to Step 9

Inspect the air temperature door and the air temperature actuator for the following conditions:

•	Misaligned air temperature actuator. Refer to Air Temperature Actuator Replacement .

•	Broken or binding linkages or air temperature door

•	Obstruction that prevents the air temperature door from operating within it's full range of motion

•	Missing seals to the air temperature door

•	Misaligned seals to the air temperature door

Did you find and correct the condition?

Go to Step 22

Go to Heating Performance Diagnostic

Test the ignition 3-voltage circuit of the air temperature actuator for an open or a high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 22

Go to Step 10

Test the ground circuit of the air temperature actuator for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 22

Go to Step 11

Test the air temperature door control circuit of the air temperature actuator for an open, high resistance, short to ground, or short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 22

Go to Step 12

Important:: Ensure that the HVAC control module connector is connected during this step in order to avoid misdiagnosis.

Turn ON the ignition, with the engine OFF.
Measure the voltage from the air temperature door control circuit of the air temperature actuator to a good ground.
Place the air temperature switch from the coldest to the warmest position.

Does the voltage measure within the specified values with a smooth transition between cold and hot?

0 V at cold

12 V at hot

Go to Step 17

Go to Step 19

Test the ignition 3-voltage circuit of the HVAC control module for an open or a high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 22

Go to Step 14

Test the battery positive voltage circuit of the HVAC control module for an open or a high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 22

Go to Step 15

Test the blower motor control OFF circuit of the HVAC control module for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 22

Go to Step 16

Test the ground circuit of the HVAC control module for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 22

Go to Step 19

Inspect for poor connections at the harness connector of the air temperature actuator. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 22

Go to Step 18

Inspect the air temperature actuator, door and any attaching linkage for binding or a condition that prevents drive shaft rotation.

Did you find and correct the condition?

Go to Step 22

Go to Step 20

Inspect for poor connections at the harness connector of the HVAC control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 22

Go to Step 21

Replace the air temperature actuator. Refer to Air Temperature Actuator Replacement - Right Side or Air Temperature Actuator Replacement - Left Side .

Did you complete the replacement?

Go to Step 22

Replace the HVAC control module. Refer to HVAC Control Module Replacement .

Did you complete the replacement?

Go to Step 22

Operate the system in order to verify the repair.

Did you correct the condition?

System OK

Go to Step 2