GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The ignition control (IC) module sends signals that the powertrain control module (PCM) requires for fuel control and spark advance calculations. At the start of engine crank, the IC module controls spark advance, called bypass mode. When the second 3X reference pulse is recognized by the PCM, the PCM applies 5 volts to the IC signal circuit, commanding the IC module to switch spark advance to PCM control (IC mode).

Conditions for Running the DTC

The engine is running.

Conditions for Setting the DTC

    •  The PCM detects an open circuit in the IC signal circuit.
    • The condition is present for 300 3X reference periods, 106 crankshaft revolutions.

Action Taken When the DTC Sets

    • The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.
    • The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records.

Conditions for Clearing the MIL/DTC

    • The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
    • A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
    • A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
    • Clear the MIL and the DTC with a scan tool.

Diagnostic Aids

The engine will start and may run in bypass mode timing.

If the condition is intermittent, refer to Intermittent Conditions .

Step

Action

Values

Yes

No

Schematic Reference: Engine Controls Schematics

1

Did you perform the Diagnostic System Check-Engine Controls?

--

Go to Step 2

Go to Diagnostic System Check - Engine Controls

2

  1. Observe the Freeze Frame/Failure Records for the DTC.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC, or within the parameters observed in the Freeze Frame/Failure Records.

Does the DTC fail this ignition?

--

Go to Step 3

Go to Intermittent Conditions

3

  1. Turn OFF the ignition.
  2. Disconnect the PCM.
  3. Turn ON the ignition.
  4. Probe the low reference circuit with a test lamp connected to battery positive voltage.

Does the test lamp illuminate?

--

Go to Step 6

Go to Step 4

4

Check the low reference circuit for an open.

Did you find and correct the condition?

--

Go to Step 6

Go to Step 5

5

Check for poor connections at the IC module.

Did you find and correct the condition?

--

Go to Step 6

Go to Step 7

6

  1. Turn OFF the ignition.
  2. Disconnect the PCM.
  3. Connect a DMM between the IC and low reference circuits.
  4. Turn ON the ignition.
  5. Probe the IC signal circuit with a test lamp connected to battery positive voltage.

Does the resistance measure greater than the specified value?

5,000 ohms

Go to Step 8

Go to Step 7

7

  1. Turn OFF the ignition.
  2. Leave the PCM disconnected.
  3. Disconnect the ignition control module connector.
  4. Test for an open in the IC signal circuit. Refer to Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 12

Go to Step 9

8

Inspect for poor terminal connections at the PCM. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 12

Go to Step 11

9

Inspect for poor terminal connections at the IC module. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 12

Go to Step 10

10

Replace the ignition control (IC) module. Refer to Ignition Control Module Replacement .

Did you complete the replacement?

--

Go to Step 12

--

11

Replace the PCM. Refer to Powertrain Control Module Replacement .

Did you complete the replacement?

--

Go to Step 12

--

12

  1. Review and record the scan tool Failure Records.
  2. Clear the DTCs.
  3. Operate the vehicle within the Failure Records conditions.
  4. Using the scan tool, monitor the Specific DTC Info for DTC P1352.

Does the scan tool indicate DTC 1352 failed this ignition?

--

Go to Step 3

Go to Step 13

13

With a scan tool, observe the stored information, Capture Info.

Does the scan tool display any DTCs that you have not diagnosed?

--

Go to Diagnostic Trouble Code (DTC) List

System OK