Refer to PCM Wiring Diagram -- Injector Schematic.
Circuit Description
The PCM controls each fuel injector separately through a ground driver circuit located within the PCM. The PCM monitors the driver circuit and has the ability to detect an electrical malfunction. If the PCM detect an electrical malfunction in the fuel injector circuit for cylinder #1, DTC P0201 will set.
Conditions for Running the DTC
The engine is running.
Conditions for Setting the DTC
| • | The PCM detects an electrical malfunction on the injector circuit for engine cylinder #1. |
| • | The condition is present for at least 30 seconds. |
Action Taken When the DTC Sets
| • | The PCM will illuminate the MIL during the second consecutive trip in which the diagnostic test has been run and failed. |
| • | If the electrical malfunction could lead to possible catalyst damage, the PCM will immediately flash the MIL while the fault remains at catalyst damage levels. |
| • | The PCM will disable TCC operation. |
| • | The PCM will store conditions which were present when the DTC set as Freeze Frame and Fail Records data. |
Conditions for Clearing the MIL/DTC
| • | The PCM will turn the MIL OFF during the third consecutive trip in which the diagnostic has been run and passed. |
| • | The history DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction. |
| • | The DTC can be cleared by using the scan tool Clear Info function or by disconnecting the PCM battery feed. |
Diagnostic Aids
The misfire history counter may be useful in determining which injector circuit is malfunctioning. If DTC P0300 was set, look at the Misfire Hist # display for each cylinder. The largest value stored in the misfire history counters will indicate the location of the malfunctioning injector circuit or injector.
Check for the following conditions:
| • | Poor connection at the PCM or fuel injector. |
| Inspect harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and poor terminal to wore connection. |
| • | Damaged harness. |
| Inspect the wiring harness for damage. |
Reviewing the Fail Records vehicle mileage since the diagnostic test last failed may help determine how often the condition that caused the DTC to be set occurs. This may assist in diagnosing the condition.
Test Description
Number(s) below refer to the step number(s) on the Diagnostic Table.
-
Checks for malfunctioning fuel injector control circuit or ignition feed wiring.
-
Checks for a malfunction in the fuel injector ignition feed circuit.
-
Checks for a short to ground in the injector control circuit.
-
Checks for an open in the fuel injector control circuit.
-
This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM is being replaced, the new PCM must be programmed.
Step | Action | Value(s) | Yes | No | ||||
|---|---|---|---|---|---|---|---|---|
1 | Was the Powertrain On-Board Diagnostic (OBD) System Check performed? | -- | ||||||
2 | With the engine idling, monitor Specific DTC info for DTC P0201 on the scan tool. Does the scan tool indicate DTC P0201 failed this ignition? | -- | ||||||
3 |
Does the scan tool indicate DTC P0201 failed this ignition? | -- | Go to Diagnostic Aids | |||||
Does the cylinder #1 fuel injector control circuit measure near the specified value? | B+ | |||||||
5 | Check the fuel injectors. Refer to Fuel Injector Solenoid Coil Test - Engine Coolant Temperature Between 10-35 Degrees C (50-95 Degrees F) or Fuel Injector Solenoid Coil Test - Engine Coolant Temperature Outside 10-35 Degrees C (50-95 Degrees F) . Are the fuel injectors OK? | -- | ||||||
6 |
Does the cylinder #1 fuel injector control circuit measure near the specified value? | 0V | ||||||
7 |
Was a problem found? | -- | ||||||
8 |
Was a problem found? | -- | ||||||
Does the ignition feed circuit measure near the specified value? | B+ | |||||||
Is the test light ON? | -- | |||||||
Is the test light ON? | -- | |||||||
12 |
Was a problem found? | -- | ||||||
13 | Locate and repair open in the cylinder #1 fuel injector control circuit. Refer to Repair Procedure in Wiring Repairs . Is action complete? | -- | -- | |||||
14 | Locate and repair open or short to ground in the cylinder #1 fuel injector ignition feed circuit. Refer to Repair Procedures in Wiring Repairs . Is action complete? | -- | -- | |||||
15 | Locate and repair short to ground in the cylinder #1 fuel injector control circuit. Refer to Repair Procedures in Wiring Repairs . | -- | -- | |||||
16 | Locate and repair short to voltage in the cylinder #1 fuel injector control circuit. Refer to Repair Procedures in Wiring Repairs . Is action complete? | 0v | -- | |||||
17 | Replace the malfunctioning fuel injector(s). Refer to Fuel Injection Fuel Rail Assembly Replacement . Is action complete? | -- | -- | |||||
Replace the PCM. Important:: The replacement PCM must be programmed. Refer to Powertrain Control Module Replacement/Programming . Is action complete? | -- | -- | ||||||
19 |
Does the scan tool indicate DTC P0201 failed this ingition? | -- | System OK |
