Circuit Description
The ignition control module (ICM) sends signals that the PCM requires for fuel control and spark advance calculations. At the start of engine crank, the ICM controls spark advance (Bypass mode). When the second 3X reference pulse is recognized by the PCM, the PCM applies 5 volts to the Bypass circuit. The 5 volts on the Bypass circuit commands the ICM to switch spark advance to PCM control (IC mode). At this time, The ICM will remove the ground it has applied to the IC circuit. When the IC pulses are not grounded, the ICM can use the IC pulses to control spark advance. A short in the IC circuit or an open or short to ground in the Bypass circuit will cause the PCM to monitor no IC pulses after the PCM has switched the Bypass circuit ON. The PCM will set DTC P1361 under either of these conditions. The engine may be started but will run on Bypass mode timing.
Condition for Running the DTC
The engine is running.
Conditions for Setting the DTC
The PCM does not monitor IC pulses while IC mode spark advance is commanded.
Action Taken When the DTC Sets
| • | The PCM will illuminate the malfunction indicator lamp (MIL) during the second consecutive trip in which the diagnostic test has been run and failed. |
| • | The PCM will store conditions which were present when the DTC set as Freeze Frame/Failure Records data. |
Conditions for Clearing the MIL/DTC
| • | The PCM will turn OFF the malfunction indicator lamp (MIL) during the third consecutive trip in which the diagnostic has run and passed. |
| • | The history DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction. |
| • | The DTC can be cleared by using a scan tool. |
Diagnostic Aids
Check for the following conditions:
| • | Poor connection at the PCM |
| Inspect harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and poor terminal to wire connection. |
| • | Damaged harness |
| Inspect the wiring harness for damage. If the harness appears to be OK, disconnect the ICM, turn the ignition ON and observe a digital multimeter connected between the IC circuit and B+ while moving connectors and wiring harnesses related to the ICM. A change in voltage will indicate the location of the malfunction. |
Reviewing the Fail Records vehicle mileage since the diagnostic test last failed may help determine how often the condition that caused the DTC to be set occurs. This may assist in diagnosing the condition.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Was the Powertrain On Board Diagnostic (OBD) System Check performed? | -- | ||
2 | Is DTC P1362 set also? | -- | ||
3 |
Is the test lamp ON? | -- | ||
4 |
Is the test lamp ON? | -- | ||
5 | Locate and repair the short to voltage in the IC circuit. Refer to Wiring Repairs . Is the action complete? | -- | -- | |
6 |
Is the test lamp ON? | -- | ||
7 | Locate and repair the short to ground in the IC circuit. Refer to Wiring Repairs . Is the action complete? | -- | -- | |
8 |
Is the test lamp ON? | -- | ||
9 | Locate and repair the short to ground in the BYPASS circuit. Refer to Wiring Repairs . Is action complete? | -- | -- | |
10 |
Was a problem found? | -- | ||
11 |
Does the voltage toggle between the two indicated ranges? | 20mV to 40mV 150mV to 250mV | ||
12 | Replace the Ignition Control Module. Refer to Ignition Control Module Replacement . Is action complete? | -- | -- | |
13 |
Important: Replacement PCM must be reprogrammed. Refer to Powertrain Control Module Replacement/Programming .Replace the PCM. Is action complete? | -- | -- | |
14 |
Does the scan tool indicate DTC P1361 failed this ignition? | -- | System OK |
