GM Service Manual Online
For 1990-2009 cars only

Tools Required

    • J 7079-2 Universal Driver Handle - Non-Threaded
    • J 8092 Universal Driver Handle - 3/4 in - 10
    • J 44375 Assembly Pallet
    • J 44376 Bearing Pusher/Puller
    • J 44377 Input Shaft Anti-Rotation Tool
    • J 44381 Shifter Bearing/Input and Output Bearing Remover
    • J 44383 Countershaft Bearing Installer
    • J 44385 Differential Bearing Race and Seal Installer
    • J 44387 Output Shaft Bearing Sleeve Installer and Pin
    • J 44389 Countershaft Bearing Installer

    Object Number: 658859  Size: SH
  1. Install the shift rod and bushing.

  2. Object Number: 762370  Size: SH
  3. Install the intermediate shaft needle bearing to the transmission housing using the J 44383  (1) and the J 8092  (2).

  4. Object Number: 658858  Size: SH
  5. Install a new shifter shaft bearing flush with the casting in the transmission housing, using the J 44381  (1) and the J 8092  (2).

  6. Object Number: 658860  Size: SH

    Important: Do not over apply the threadlocker to the bolt threads.

  7. Apply GM P/N United States 12345382, GM P/N Canada 10953489 to the reverse lockout lever bolt threads.
  8. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

    Important: The spring (2) fingers must be positioned on either side of the lever (3).

  9. Install the reverse lockout lever (3), spring (2), and the bolt (1) to the transmission housing, if equipped.
  10. Tighten
    Tighten the bolt to 6 N·m (53 lb in).


    Object Number: 658871  Size: SH
  11. Install a new differential bearing race to the transmission housing using theJ 44385  (2) and the J 7079-2  (1).

  12. Object Number: 660201  Size: SH
  13. Install a new differential side bearing race seal to the transmission housing using the J 44385  (2) and the J 7079-2  (1).

  14. Object Number: 658878  Size: SH
  15. Install the countershaft bearing to the clutch housing using the J 44381  (1) and the J 7079-2  (2).
  16. Install a new snap ring.

  17. Object Number: 747502  Size: SH
  18. Install the input shaft bearing to the clutch housing using the J 44381  (2) and the J 7079-2  (1).

  19. Object Number: 658868  Size: SH
  20. Install the output shaft bearing race and bolts using the J 44387-1 (2), J 44387-2 (3), and the J 7079-2  (1).
  21. Tighten
    Tighten the output shaft bearing bolts to 10 N·m (89 lb in).


    Object Number: 658872  Size: SH
  22. Install a new differential bearing race to the clutch housing using the J 44385  (2) and the J 7079-2  (1).

  23. Object Number: 658880  Size: SH
  24. Install a new differential output shaft seal to the clutch housing using theJ 44385  (2) and the J 8092  (1).

  25. Object Number: 658882  Size: SH
  26. Install the snap rings to the input shaft and output shaft bearings.
  27. Install the input shaft and output shaft bearings into the transmission housing using the J 44385  (2) and the J 7079-2  (1).

  28. Object Number: 634461  Size: SH
  29. Install the shift forks and the input shaft and output shaft onto the J 44375 .

  30. Object Number: 634460  Size: SH
  31. Install the countershaft and the shift fork onto the J 44375 .
  32. Rotate the shaft to verify all gears are properly meshing.

  33. Object Number: 634463  Size: SH
  34. Install the housing onto the shift forks and the shafts on to the J 44375 . Line up the shift forks and the shafts with the housing.

  35. Object Number: 658883  Size: SH

    Important: Install the transaxle case to the shafts evenly using the J 44376 .

  36. Install the transaxle case to the shafts using the J 44376 .

  37. Object Number: 513921  Size: SH
  38. Shift the transmission into 4th and 5th gear using a screwdriver in an upward direction.
  39. Apply GM P/N United States 12345493, GM P/N Canada 10953488 to the input and output shaft bolts.
  40. Install NEW input and output shaft bolts while holding the transmission into 4th and 5th gear in an upward direction.
  41. Tighten
    Tighten the shaft bolts to 110 N·m (81 lb ft).


    Object Number: 514887  Size: SH

    Important: If shimming is required, refer to Shimming Procedures before installing the cover.

  42. Install sealant GM P/N United States 12346286, GM P/N Canada 10953472 to the rear cover.

  43. Object Number: 513914  Size: SH

    Important: The oil guide only installs in one direction. Ensure the oil guide is completely seated in the gear shafts.

  44. Install the oil guide.
  45. Install the rear cover.
  46. Install the rear cover bolt.
  47. Tighten
    Tighten the rear cover bolt to 25 N·m (18 lb ft).


    Object Number: 514888  Size: SH
  48. Apply sealant GM P/N United States 12346004, GM P/N Canada 10953480 to the backup lamp switch.
  49. Install the backup lamp switch into the transaxle case.
  50. Tighten
    Tighten the backup lamp switch to 18 N·m (13 lb ft).


    Object Number: 634458  Size: SH
  51. Turn the transaxle case and the J 44375 over on the table.
  52. Remove the J 44375 from the gear shafts and the shift forks.

  53. Object Number: 513926  Size: SH
  54. Install the oil tube into the transaxle case.

  55. Object Number: 679562  Size: SH
  56. Install the shift rod to the shift fork.

  57. Object Number: 514892  Size: SH

    Important: Use only the approved sealer for the transaxle case to shifter cover mating surface.

  58. Apply sealer GM P/N United States 12378516, GM P/N Canada 88900757 to the transaxle case to shifter cover mating surface.

  59. Object Number: 513882  Size: SH
  60. Install the shifter and the shifter retaining bolts.
  61. Tighten
    Tighten the shifter retaining bolts to 25 N·m (18 lb ft).

    Install all possible shifter bolts with the shifter in the neutral position. Install the last shifter bolt in gear and then shift the transmission back into neutral.


    Object Number: 513880  Size: SH
  62. Shift the transmission into neutral.
  63. Apply GM P/N United States 12346004, GM P/N Canada 10953480 to the shifter guide bolt.
  64. Notice: Hand start and tighten the shifter guide bolt to avoid damaging the shift lever.

  65. Install the shifter guide bolt.
  66. Tighten
    Tighten the shifter guide bolt to 25 N·m (18 lb ft).


    Object Number: 513904  Size: SH
  67. Install the differential into the transaxle case.

  68. Object Number: 513908  Size: SH

    Important: The step in the roller bearing faces opposite of the pinion gear.

  69. Install the roller bearing onto the output shaft.

  70. Object Number: 514837  Size: SH
  71. Install the magnet into the transaxle case.

  72. Object Number: 514893  Size: SH
  73. Apply sealant GM P/N United States 12378516, GM P/N Canada 88900757 to the transaxle case to clutch housing mating surface.

  74. Object Number: 513889  Size: SH
  75. Install the clutch housing to the transaxle case.

  76. Object Number: 681423  Size: SH
  77. Install the countershaft into the clutch housing bearing using the J 44389 .

  78. Object Number: 513885  Size: SH
  79. Install the clutch housing to transaxle case bolts.
  80. Tighten
    Tighten the housing bolts to 27 N·m (20 lb ft).


    Object Number: 513865  Size: SH
  81. Turn the transmission over.
  82. Install the transaxle case to clutch housing bolts.
  83. Tighten
    Tighten the housing bolts to 27 N·m (20 lb ft).


    Object Number: 513877  Size: SH
  84. Turn the transmission so the shifter is on top.
  85. Shift the transmission into any gear.

  86. Object Number: 658861  Size: SH
  87. Install the input shaft seal to the actuator.
  88. Install the actuator and tube.
  89. Install the actuator and tube bolts.
  90. Tighten
    Tighten the tube bolts to 10 N·m (89 lb in).


    Object Number: 747503  Size: SH
  91. Apply GM P/N United States 12346004, GM P/N Canada 10953480 to the transmission drain plug.
  92. Install the transmission drain plug.
  93. Tighten
    Tighten the transmission drain plug to 38 N·m (28 lb ft).


    Object Number: 747504  Size: SH
  94. Install the transmission fill cap.

  95. Object Number: 634456  Size: SH
  96. Hold the input shaft with the J 44377 .
  97. Apply GM P/N United States 12345493, GM P/N Canada 10953488 to the intermediate shaft bolt.
  98. Install the bolt in the intermediate shaft.
  99. Tighten
    Tighten the intermediate shaft bolts to 95 N·m (70 lb ft).


    Object Number: 513875  Size: SH
  100. Install a new plastic oil guide into the intermediate shaft.

  101. Object Number: 513872  Size: SH

    Important: Ensure not to press the sealing cap past the bottom of the chamfer.

  102. Install a new intermediate shaft sealing cap.

  103. Object Number: 658863  Size: SH
  104. Apply GM P/N United States 12345382, GM P/N Canada 10953489 to the vehicle speed sensor bolt.
  105. Install the vehicle speed sensor, seal, and bolt.
  106. Tighten
    Tighten the bolt to 12 N·m (8 lb ft).


    Object Number: 679569  Size: SH
  107. Install the shift cable bracket (4), the isolators (3), the spacers (2) and the bolt (1).
  108. Tighten
    Tighten the shift cable bracket bolt to 20 N·m (15 lb ft).