GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The PCM uses the generator turn on signal circuit to control the load of the generator on the engine. A high side driver in the PCM applies a voltage to the voltage regulator. This signals the voltage regulator to turn the field circuit ON and OFF. When the PCM turns ON the high side driver, the voltage regulator turns ON the field circuit. When the PCM turns OFF the high side driver, the voltage regulator turns OFF the field circuit.

The PCM monitors the state of the generator turn on signal circuit. The PCM should detect a low generator turn on signal circuit voltage when the key is ON and the engine is OFF, or when the charging system malfunctions. With the engine running, the PCM should detect a high generator turn on signal circuit. The PCM performs key ON and RUN tests to determine the status of the generator turn on signal circuit. During the key ON test, if the PCM detects a high generator turn on signal circuit voltage, DTC P0621 will set. DTC P0621 will also set if, during the RUN test, the PCM detects a low generator turn on signal circuit. When the DTC sets, the PCM will send a class 2 serial data message to the IPC to illuminate the charge indicator.

Conditions for Running the DTC

Key ON Test

    • No generator, CKP sensors, or CMP sensor DTCs are set.
    • The key is in the RUN position.
    • The engine is not running.

Run Test

    • No generator, CKP sensors, or CMP sensor DTCs are set.
    • The engine is running.

Conditions for Setting the DTC

    • During the key ON test, the PCM detects a high signal voltage on the generator turn on signal circuit for at least 5 seconds.
        OR
    • During the RUN test, the PCM detects a low signal voltage on the generator turn on signal circuit for at least 15 seconds.

Action Taken When the DTC Sets

    • The PCM will not illuminate the Malfunction Indicator Lamp (MIL)
    • The PCM will store the conditions present when the DTC set as Fail Records data only.

Conditions for Clearing the MIL/DTC

    • The history DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
    • The DTC can be cleared by using the scan tool Clear DTC Information function.

Step

Action

Yes

No

Schematic Reference: Starting and Charging Schematics

1

Did you perform the Engine Electrical Diagnostic System Check?

Go to Step 2

Go to Diagnostic System Check - Engine Electrical

2

  1. Install a scan tool.
  2. Start the engine.
  3. With a scan tool, monitor the DTC information for DTC P0621 in Engine Controls.

Does the scan tool indicate that DTC P0621 has passed?

Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

Go to Step 3

3

With a scan tool, monitor the DTC information for DTC P0621 and DTC P0622 in Engine Controls.

Does the scan tool indicate that DTC P0621 and DTC P0622 have failed?

Go to Step 6

Go to Step 4

4

Test the generator turn on signal circuit for a short or open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 8

Go to Step 5

5

Inspect for poor connections at the harness connector of the PCM. Refer to Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 8

Go to Step 7

6

Repair the high resistance or open in the battery positive voltagel circuit of the generator. Refer to Wiring Repairs in Wiring Systems.

Did you complete the repair?

Go to Step 8

--

7

Important: The replacement PCM must be programmed. Refer to Powertrain Control Module Programming in Engine Controls-2.2L.

Replace the PCM. Refer to Powertrain Control Module Replacement in Engine Controls-2.2L.

Did you complete the replacement?

Go to Step 8

--

8

  1. Review and record the scan tool Fail Records data.
  2. Use the scan tool in order to clear the DTC.
  3. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.
  4. Using the scan tool, observe the Specific DTC Information for DTC P0621 until the test runs.

Does the scan tool indicate that DTC P0621 failed this ignition?

Go to Step 2

System OK