Water Pump Replacement 2.4L

1. Drain the coolant. Recover the coolant. Refer to Cooling System Draining and Filling .
2. Remove the exhaust manifold. Refer to Exhaust Manifold Replacement in Engine Exhaust.



3. Remove the coolant intake pipe. Refer to Engine Coolant Inlet Pipe Replacement in Engine Cooling.
4. Lower the vehicle.
5. Disconnect the heater hose quick connect from the heater outlet pipe.
6. Remove the timing chain and tensioner. Refer to Camshaft Timing Chain, Sprocket, and Tensioner Replacement in Engine Mechanical - 2.4L.



7. Remove the water pump cover-to-cylinder block bolts.
8. Remove water pump pipe to cylinder block bolt.



9. Remove the 3 water pump-to-timing chain housing nuts.
10. Remove the water pump and cover assembly.
11. Remove the water pump cover-to-coolant pump assembly bolts.
12. Clean all sealing surfaces.

Important: Before you install the coolant pump, read the entire procedure. Follow the tightening sequences in order to avoid part damage and to provide proper sealing.




1. Install the water pump cover to the water pump assembly.
2. Install the pump cover bolts. Hand tighten the bolts.
3. Install water pump cover assembly.



4. Install the cover-to-block bolts. Hand tighten the bolts.
5. Install the coolant pump-to-timing chain housing nuts. Hand tighten the nuts.




Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

6. Torque in sequence as follows:

6.1.	Tighten the water pump-to-timing chain housing nuts.

Tighten
Tighten water pump to timing chain housing nuts to 26 N·m (19 lb ft).

6.2.	Tighten the pump cover-to-pump assembly bolts.

Tighten
Tighten the water pump cove to water pump bolts to 14 N·m (124 lb in).

6.3.	Tighten the coolant pump cover-to-engine block bolts. Tighten the bottom bolt first.

Tighten
Tighten water pump to engine block bolts to 26 N·m (19 lb ft).

7. Install heater hose to pipe on water pump.
8. Install the exhaust manifold and install new gaskets. Refer to Exhaust Manifold Replacement in Engine Exhaust.
9. Install oil level indicator tube and indicator. Refer to Oil Level Indicator and Tube Replacement in Engine Mechanical-2.4L.
10. Connect the brake vacuum pipe to the cam housing.
11. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
12. Install catalytic converter to to manifold. Refer to Catalytic Converter Replacement in Engine Exhaust.
13. Install the coolant inlet pipe. Refer to Engine Coolant Inlet Pipe Replacement .
14. Install the timing chain and tensioner. Refer to Camshaft Timing Chain, Sprocket, and Tensioner Replacement in Engine Mechanical - 2.4L.
15. Lower the vehicle.
16. Connect the oxygen sensor connector.
17. Fill cooling system. Refer to Cooling System Draining and Filling in Engine Cooling.
18. Inspect the system for leaks.

Water Pump Replacement 3.4L

1. Drain the cooling system. Refer to Cooling System Draining and Filling .
2. Loosen the water pump pulley bolts.
3. Remove the drive belt. Refer to Drive Belt Replacement in Engine Mechanical-3.1L.



4. Remove the water pump pulley bolts and pulley.
5. Remove the water pump bolts, pump and gasket.
6. Clean the water pump mating surfaces.

1. Install the water pump gasket and pump (1).

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the water pump bolts.

Tighten
Tighten the bolts to 10 N·m (89 lb in).




3. Install the water pump pulley and bolt until snug.
4. Install the drive belt. Refer to Drive Belt Replacement in Engine Mechanical-3.1L.
5. Tighten the water pump pulley bolts.

Tighten
Tighten the bolts to 25 N·m (18 lb ft).

6. Fill the cooling system. Refer to Cooling System Draining and Filling .
7. Inspect for leaks.