Circuit Description
The powertrain control module (PCM) enables the appropriate fuel injector on the intake stroke for each cylinder. An ignition voltage is supplied to the fuel injectors. The PCM controls each fuel injector by grounding the control circuit via a solid state device called a driver. The PCM monitors the status of each driver. If the PCM detects an incorrect voltage for the commanded state of the driver, a fuel injector control DTC sets.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P0200 Injector Control Circuit
Conditions for Running the DTC
| • | The engine speed is more than 400 RPM. |
| • | The ignition voltage is between 6-18 volts. |
Conditions for Setting the DTC
| • | The PCM detects an incorrect voltage on a fuel injector control circuit. |
| • | The condition exists for 5 seconds. |
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Diagnostic Aids
| • | Performing the Fuel Injector Coil test may help isolate an intermittent condition. Refer to Fuel Pump Electrical Circuit Diagnosis. |
| • | For an intermittent condition, refer to Testing for Intermittent Conditions and Poor Connections. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step tests for voltage at the fuel injector harness connector. The INJ fuse supplies power to the coil side of the fuel injector harness connector. If the fuse is open, a short to ground on the fuel injector B+ supply circuit is indicated.
-
This step verifies that the PCM is able to control the fuel injector. If the test lamp blinks, then the PCM and wiring are OK.
-
This step tests if a ground is constantly being applied to the fuel injector.
Step | Action | Yes | No |
|---|---|---|---|
Schematic Reference: Engine Controls Schematics Connector End View Reference: Component Connector End Views | |||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | |
2 |
Are any of the misfire current counters incrementing? | Go to Step 4 | Go to Step 3 |
3 |
Does the DTC fail this ignition? | Go to Step 4 | Go to Diagnostic Aids |
Does the test lamp illuminate? | Go to Step 5 | Go to Step 11 | |
Does the test lamp blink? | Go to Step 9 | Go to Step 6 | |
Does the test lamp remain illuminated at all times? | Go to Step 8 | Go to Step 7 | |
7 | Test the control circuit of the fuel injector for a short to voltage or an open. Refer to Circuit Testing and Wiring Repairs. Did you find and correct the condition? | Go to Step 14 | Go to Step 10 |
8 | Test the control circuit of the fuel injector for a short to ground. Refer to Circuit Testing and Wiring Repairs. Did you find and correct the condition? | Go to Step 14 | Go to Step 13 |
9 | Inspect for poor connections at the harness connector of the fuel injector. Refer to Testing for Intermittent Conditions and Poor Connections and Repairing Connector Terminals. Did you find and correct the condition? | Go to Step 14 | Go to Step 12 |
10 | Inspect for poor connections at the harness connector of the powertrain control module (PCM). Refer to Testing for Intermittent Conditions and Poor Connections and Repairing Connector Terminals. Did you find and correct the condition? | Go to Step 14 | Go to Step 13 |
11 |
Important: The INJ fuses also supply voltage to the ignition coil modules. If a fuse is open, inspect all related circuits for a short to ground. Did you complete the repair? | Go to Step 14 | -- |
12 | Replace the fuel injector. Refer to Fuel Injector Replacement. Did you complete the replacement? | Go to Step 14 | -- |
13 | Replace the PCM. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement? | Go to Step 14 | -- |
14 |
Does the DTC run and pass? | Go to Step 15 | Go to Step 2 |
15 | Observe the Capture Info with a scan tool. Does the scan tool display any DTCs that you have not diagnosed? | System OK | |
