Diagnostic Instructions
DTC Descriptor
DTC P1574: Stoplamp Switch Circuit
Diagnostic Fault Information
Circuit
| Short to Ground
| Open/High Resistance
| Short to Voltage
| Signal Performance
|
B+
| P1574
| P1574
| --
|
|
Cruise Control Release Switch Signal
| P1574
| P1574
| P1574
| --
|
Circuit/System Description
This diagnostic test functions on the assumption that a sudden decrease in vehicle speed is caused by a brake pedal application. When the engine control module (ECM) detects that there is a 4.2 km/h (2.6 mph) or greater decrease in vehicle
speed within 0.25 second and a transition of the torque converter clutch (TCC) brake switch without a transition of the stop lamp switch, the ECM sets DTC P1574.
Conditions for Running the DTC
| • | DTCs P0502, P0503, P0719, and P0724 are not set. |
| • | The engine speed is greater than 700 RPM. |
| • | The traction control system or the antilock brake system are not active and have not failed. |
| • | The vehicle speed is greater than 48 km/h (30 mph) in order to enable the diagnostic. |
| • | The diagnostic will disable when the wheel speed is less than 16 km/h (10 mph). |
Conditions for Setting the DTC
| • | The vehicle speed decreases by at least 4.2 km/h (2.6 mph) within 0.25 second. |
| • | The ECM detects a TCC brake transition. |
| • | The ECM does not detect a stop lamp switch transition. |
Actions Taken When the DTC Sets
| • | The malfunction indicator lamp (MIL) will not illuminate. |
| • | The cruise control system is disabled. |
Conditions for Clearing the DTC
| • | The condition responsible for setting the DTC no longer exists. |
| • | A history DTC will clear after 40 malfunction-free ignition cycles have occurred. |
Diagnostic Aids
Observe the stop lamps operate properly. Refer to
Exterior Lighting Systems Description and Operation in order to avoid misdiagnosis.
Reference Information
Schematic Reference
Cruise Control Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
Cruise Control Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
Ignition ON, observe the TCC/Cruise Brake Pedal Switch parameter while applying and releasing the brake pedal. The reading should change between Applied and Released.
Circuit/System Testing
- Ignition OFF, disconnect the harness connector at the cruise control release switch.
- Ignition ON, test for B+ between the B+ circuit terminal 1 and ground.
| ⇒ | If less than the specified value, test the B+ circuit for a short to ground or an open/high resistance. |
- Verify the scan tool TCC/Cruise Brake Pedal Switch parameter displays Released.
| ⇒ | If not the specified value, test the signal circuit terminal 2 for a short to voltage. If the circuit tests normal, replace the ECM. |
- Install a 3A fused jumper wire between the signal circuit terminal 2 and the B+ circuit terminal 1. Verify the scan tool TCC/Cruise Brake Pedal Switch parameter displays Applied.
| ⇒ | If not the specified value, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the ECM. |
- If all circuits test normal, test or replace the cruise control release switch.
Component Testing
- Ignition OFF, disconnect the harness connector at the cruise control release switch.
- Test for less than 1 ohm between terminals 1 and 2 at the switch.
| ⇒ | If not the specified value, replace the cruise control release switch. |
- Depress the brake pedal. Test for infinite resistance between terminals 1 and 2 at the switch.
| ⇒ | If not the specified value, replace the cruise control release switch. |
Repair Instructions
Perform the
Diagnostic Repair Verification after completing the diagnostic procedure.
