The CTD system (when armed) is designed to deter vehicle content theft by pulsing the horns and exterior lamps for approximately 2 minutes when an unauthorized vehicle entry is detected. However, the CTD system does not affect engine starting.

An unauthorized entry can be any of the following with the CTD system armed:

The components of the system are:

Important: The CTD system can be armed with the windows or sunroof open.

Use the following procedure in order to arm the system:

1. Place the shift lever in P (park).
2. Turn OFF the ignition.
3. Open any door.

Important: The system is not armed if the doors are locked manually, the power door lock switch or remote keyless entry transmitter must be used to arm the CTD system.

The CTD system will not arm from the power door lock switch if all doors are closed.
4. Lock the doors with the power door lock switch or the LOCK button on the transmitter. The system is in arm pending mode and will not start the arming timer until all doors are closed. The security indicator will flash indicating arm pending mode. The CTD system will arm after the last door is closed.
5. The system will arm approximately 30 seconds from the time that the last door is closed. This delay is shown by the SECURITY indicator ON STEADY. When the indicator transitions to OFF, the system is armed.

Locking the vehicle may be accomplished without arming the CTD system. Use of the manual door locks or using the key to lock the doors will lock the vehicle but will not arm the CTD system.

If system arming has been requested by the power door lock switch or the keyless entry transmitter, it must be disarmed.

Important: Using the power door unlock switch or manually unlocking the doors from inside the vehicle does not disable the CTD armed mode. Also, disconnecting the battery or pulling fuses does not disable the armed mode, since the BCM stores the CTD mode status in memory.

The following is a description of components used in the CTD system:

The CTD system is an internal function of the Body Control Module (BCM) which utilizes class 2 serial data from the driver door module (DDM), Passenger door module (PDM) and the liftgate module (LGM) and various switch input information to perform CTD functions. When the BCM detects an unauthorized entry, it activates the horns and exterior lamps.

When the BCM detects an unauthorized entry, the BCM enters the alarm mode. The BCM activates the horns and exterior lamps for 2 minutes. This is followed by a three minute time-out with the horn no longer active. If no new intrusions are detected after the time-out, the horn is not active. The system must be disarmed or the intrusion condition removed after the time-out for the system to exit alarm mode.

The CTD system uses the rear door ajar switches in the door lock assemblies as one method to activate the alarm. The body control module (BCM) monitors rear door ajar switches via a discrete input from each rear passenger door ajar switch, if the BCM receives a ground signal from a rear passenger door ajar switch when the CTD system is armed, the BCM activates the alarm.

The CTD system uses the LH front door ajar switch as one method to activate the alarm. The driver door module (DDM) monitors the LH door ajar switch via a discreet input from the door ajar switch, if the DDM receives a ground signal from the LH door ajar switch when the CTD system is armed the message is communicated through the serial data circuit to the BCM and the alarm is activated.

The CTD system uses the RH front door ajar switch as one method to activate the alarm. The passenger door module (PDM) monitors the RH door ajar switch via a discreet input from the door ajar switch, if the PDM receives a ground signal from the RH door ajar switch when the CTD system is armed the message is communicated through the serial data circuit to the BCM and the alarm is activated.

The CTD system uses the rear compartment liftgate/liftglass ajar switchs as one method to activate the alarm. The liftgate module (LGM) monitors the liftgate and liftglass ajar switch via a discreet input from the ajar switch, if the LGM receives a ground signal from the liftgate or liftglass ajar switch when the CTD system is armed the message is communicated through the serial data circuit to the BCM and the alarm is activated.

The power door lock switches are used to either arm or disarm the CTD system. Pressing the lock position will cause the CTD to arm after all doors are closed and the 30 second delay period has elapsed. Pressing the unlock position will disarm the CTD system.

The BCM monitors directly or serial data communication the following inputs:

Outputs

The BCM controls the following: