Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptor
DTC B2625 00: Display Dimming Pulse Width Modulation (PWM) Output CircuitDiagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
TBC 2 Fuse B+ | 2 | 2 | -- | -- |
TBC 5 Fuse B+ | 2 | 2 | -- | -- |
I/P Dimming Voltage Reference | 1 | 1 | 1 | -- |
I/P Dimmer Switch Control | 1 | 1 | 1 | -- |
I/P Lamps Dimmer Switch Signal | 2 | 2 | 2 | -- |
Indicator Dimming Control | B2625 00 | B2625 00 | B2625 00 | -- |
LED Backlight Dimming Signal | B2610 00 | 3 | 3 | -- |
LED Backlight Dimming Control | 3 | 3 | 3 | -- |
Memory Switch Backlight Control | 4 | 4 | 4 | -- |
I/P Dimmer Low Reference | 1 | 1 | 1 | -- |
Memory Switch Backlight Low Reference | -- | 4 | -- | -- |
Headlamp Switch Ground | -- | 1 | -- | -- |
1. Dimmer Switch Malfunction 2. Interior Backlighting Malfunction -- Incandescent 3. Interior Backlighting Malfunction -- LED 4. Memory Switch Indicator Malfunction | ||||
Circuit/System Description
When the ignition switch is turned to the RUN position, the radio's VF displays turn ON at maximum brightness. When the park lamps are ON, all incandescent back lighting turn ON at the dimming level indicated by the instrument panel (I/P) dimmer switch. At the same time all VF displays dim to match the indicated dimming level. The panel dimmer switch potentiometer is an input to the body control module (BCM). When the driver selects a dimming setting by moving the I/P dimming switch potentiometer, all incandescent back lighting lamps are provided with a specific voltage. The incandescent back lighting lamps are then grounded at G201, G302, and G303. When the I/P dimmer switch is moved from MIN to MAX, all vacuum fluorescent (VF) displays, as well as all incandescent back lighting respond from minimum intensity to maximum brightness in response to the I/P dimmer switch.
Conditions for Running the DTC
The battery voltage must be between 9-16 volts.
Conditions for Setting the DTC
| • | The TBC 4 fuse battery supply circuit to the BCM is open or shorted to ground. |
| • | The LED dimming supply voltage circuit is shorted to ground. |
Action Taken When the DTC Sets
The switch LED indicators will be inoperative.
Conditions for Clearing the DTC
| • | This DTC will clear on current status after the condition for setting the fault is corrected. |
| • | A history DTC will clear after 100 consecutive ignition cycles without a fault present. |
Reference Information
Schematic Reference
Interior Lights Dimming Schematics
Connector End View Reference
Description and Operation
Interior Lighting Systems Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Testing
- Ignition OFF, disconnect the BCM connector X3.
- Verify that a test lamp illuminates between the B+ circuit terminal B4 and ground.
- If the circuits test normal, replace the BCM.
| ⇒ | If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. If the circuit tests normal, and the B+ circuit fuse is open, test the courtesy lamp supply circuit terminal B3 for a short to ground. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
Control Module References for BCM replacement, programming, and setup
