GM Service Manual Online
For 1990-2009 cars only

Repeater Lamp Replacement SWB

Removal Procedure - Side Indicator Type A

    Caution: Refer to Battery Disconnect Caution in the Preface section.

  1. Disconnect the battery ground cable. Refer to Battery Negative Cable Disconnection and Connection.

  2. Object Number: 1946830  Size: SH
  3. Remove side indicator lamp assembly from the fender by grasping the assembly and pushing the assembly forward to disengage the rear clip from the fender.
  4. Tilt the rear of the side indicator lamp assembly out and remove the assembly from the front fender.
  5. Disconnect the bulb socket from the side indicator lamp assembly by rotating the socket counterclockwise.
  6. Disconnect the electrical connector from the bulb socket, by depressing the connector clip and pulling connector from bulb socket.
  7. Discard the repeater lamp.

Installation Procedure - Side Indicator Type A


    Object Number: 1947032  Size: SH
  1. Install the bulb socket into the new side indicator lamp assembly and rotate the socket clockwise to secure the bulb.
  2. Connect electrical connector to the bulb socket, note oretayion of the electrcal connector.
  3. Install rear portion of the side indicator lamp assembly into the fender and then push the front of the lamp assembly inwards to engage the front clip.
  4. Caution: Refer to Battery Disconnect Caution in the Preface section.

  5. Connect the battery ground cable. Refer to Battery Negative Cable Disconnection and Connection.
  6. Check all vehicle lights for correct operation.

Repeater Lamp Replacement LWB

Removal Procedure - Side Indicator Type B

    Caution: Refer to Safety Glasses Caution in the Preface section.

    Caution: Refer to Vehicle Lifting Caution in the Preface section.

  1. Raise and support the vehicle to a suitable working height. Refer to Lifting and Jacking the Vehicle.
  2. Remove the front wheelhouse liner. Refer to Front Wheelhouse Liner Replacement.

  3. Object Number: 1947033  Size: SH
  4. Unclip the side indicator (2) retaining clips (1) and detach from the fender.

  5. Object Number: 1947036  Size: SH
  6. Disconnect the side indicator lamp (2) electrical connector (1).
  7. Remove the side indicator lamp (2).

Installation Procedure


    Object Number: 1947036  Size: SH
  1. Connect the side indicator lamp (2) electrical connector (1).

  2. Object Number: 1947033  Size: SH
  3. Align the side indicator lamp (2) with the fender.
  4. Install the side indicator lamp (2) into the fender, ensuring that the retaining clips (1) are fully located in the fender. Listen for an audible click to confirm fitting.
  5. Install the front wheelhouse liner. Refer to Front Wheelhouse Liner Replacement.
  6. Lower the vehicle.
  7. Test the side indicator lamp for correct operation.

Repeater Lamp Replacement CSV SWBHSV VXR8

Removal Procedure - Side Indicator Type C

    Caution: Refer to Battery Disconnect Caution in the Preface section.

  1. Disconnect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection .
  2. Remove the fender vent. Refer to Front Fender Center Molding Replacement

  3. Object Number: 1947034  Size: SH
  4. Using a suitable tool, release the side indicator lamp retaining clip (1) and remove the side indicator lamp (2).

Installation Procedure - Side Indicator Type C

  1. Install the side indicator lamp to the fender vent.
  2. Install the fender vent. . Refer to Front Fender Center Molding Replacement
  3. Caution: Refer to Battery Disconnect Caution in the Preface section.

  4. Connect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection .