GM Service Manual Online
For 1990-2009 cars only

Interior Lamps

The interior lighting consists of 2 groups. The first group includes lamps that may not be dimmed.

    • Courtesy/illuminated entry lamps
    • Dome lamps
    • Vanity mirror lamps

Courtesy/Illuminated Entry Lamps

The courtesy/illuminated entry lamps, may be manually turned ON or OFF by placing the interior lamp switch in the ON or OFF position. If an outside door handle is lifted and a door is opened, the courtesy/illuminated entry lamps illuminate. After the doors have been closed the courtesy/illuminated entry lamps will remain illuminated for approximately 15 seconds. The body control module (BCM) will then turn them OFF through the theatre dimming feature. The courtesy/illuminated entry lamps will also turn ON prior to any door being opened, and remain illuminated for approximately 40 seconds when the driver removes the ignition key. When the driver places the dome lamp switch in the OFF position, the courtesy/illuminated entry lamps will be disabled.

The lamp illumination commands for the door ajar switch signals are communicated from the door ajar switches to the BCM via the GMLAN serial data circuit.

The left and right front door courtesy lamps receive voltage and ground from the driver door switch and the passenger door switch respectively. The courtesy lamp supply voltage circuit is supplied from the INT LTS fuse in the instrument panel fuse block.

Load Compartment Light - HSV Maloo

The load compartment light is controlled by the dome lamp control circuit. There is not a separate switch to turn the load compartment light ON and OFF.

Keyless Entry Interior Illumination

When the driver uses the door key in order to unlock the doors, the BCM receives a door unlock signal. The BCM must have inputs or serial data messages that indicate that the ignition switch is OFF, the courtesy lamp switch is OFF and the doors are closed. The BCM will then activate the interior lamps. The courtesy lamps will remain ON, approximately 15 seconds after the door is closed. The BCM will then turn them OFF through the theatre dimming feature. If the door locks are activated to the LOCK position, or if the ignition switch is turned to either the RUN or CRANK position the courtesy lamps will turn OFF immediately.

When the driver uses the remote function actuator transmitter to unlock the doors, or presses the panic button, the BCM will keep the courtesy lamps ON approximately 40 seconds. When the driver uses the remote function actuator transmitter to lock the doors, the BCM will keep the courtesy lamps on approximately 2 seconds. If the ignition switch is turned to either the RUN or CRANK position the courtesy lamps will turn OFF immediately.

Vanity Lamps

The inadvertent power supply voltage circuit of the BCM provides battery positive voltage to each vanity mirror lamp. When the vanity mirror cover on the sunshade is opened, a switch closes to provide a ground circuit and the vanity lamp illuminates.

Battery Rundown Protection/Inadvertent Power

The BCM inadvertent power supply voltage circuit provides battery positive voltage to the interior visor vanity mirror lamps. In the event that these lamps were to remain illuminated for a period of more than 10 seconds with the ignition switch in the OFF position, the BCM will deactivate the inadvertent power supply voltage circuit to prevent a total battery discharge condition.

Interior Lamps Dimming

The second interior lighting group includes lamps which may be dimmed. This group may use a combination of vacuum fluorescent (VF) illumination, LED illumination and incandescent lamps.

When the ignition switch is turned to the RUN position, the radio VF display turns ON at maximum brightness. When the park lamps are ON, all incandescent and LED back lighting turn ON at the dimming level indicated by the instrument panel (I/P) dimmer switch. At the same time all VF displays dim to match the indicated dimming level. The panel dimmer switch potentiometer is an input to the BCM. When the driver selects a dimming setting by moving the I/P dimming switch potentiometer, all incandescent back lighting lamps are provided with a specific voltage. When the I/P dimmer switch is moved from MIN to MAX, all VF displays, as well as all incandescent back lighting respond from minimum intensity to maximum brightness in response to the I/P dimmer switch.

The following switches and components have back lighting when the park lamps are ON:

    • The instrument panel cluster (IPC)
    • Accessory switches
    • Fog lamp switches
    • PRNDL lamps
    • Traction control switch
    • Steering wheel control switches

The left and right front door switch illumination is controlled, receives voltage and ground from the driver door switch and passenger switch respectively. The radio is also a GMLAN module and has full control of its illumination. The BCM, door switches, and radio communicate through GMLAN serial data for the lamp illumination commands.

The various switches, HVAC control assembly, and the PRNDL lamps receive voltage and are controlled by the BCM on the I/P lamps dimming control circuit.

The following indicators receive voltage from the BCM and are controlled by ground from a switch or from various modules:

    • Tow indicator
    • Radio
    • HVAC control assembly
    • Instrument panel cluster (IPC)
    • Driver information centre (DIC)
    • Headlamp and panel dimmer switch

The indicators receive voltage from the BCM on the LED dimming circuit. Control for the indicators is from the various modules or switches. Voltage for the LED dimming supply circuit, instrument panel lamps dimming control circuit and the instrument panel lamps dimming supply circuit is from the BCM.