Dimensions - Body. Holden Captiva 2007

For 1990-2009 cars only

Makes 🢒 Holden 🢒 2007 🢒 Captiva 🢒 Preface 🢒 Cautions and Notices 🢒 Dimensions - Body

Dimensions - Body C100/Long Body

Table 1:	Front Compartment Dimensions
Table 2:	Body Dimensions (Long Body)
Table 3:	Underbody Dimensions

Three Dimensional Distance -- X, Y, Z

This universal measuring system is capable of simultaneously dimensioning the length, width, and height of a datum plane. Three dimensional distances are used for both underbody and upperbody measuring.

X = Fore and aft measurements along the center line of the vehicle. An O plane is located forward of the master gage hole at the front of the vehicle. All measurements are made from this plane toward the rear of the vehicle.

Y = Cross car dimensions. Positive values are measured from the center of the vehicle to the right side of the vehicle. Negative values are measured from the center of the vehicle to the left side. When values are not listed separately to change the side of the vehicle, you need only to change the Y dimensions to the opposite value, + or -, from what is listed.

Z = Vertical measurement from the datum plane below the rocker panel lower flange edge (O plane).

All dimensions are symmetrical, unless otherwise noted.

In order to properly repair the spaceframe, restore the vehicle to the XYZ dimensions, as originally built. Relational (linear) dimensions are for reference only. Use relational dimensions for diagnosis or inspection only. Relational dimensions are not as accurate as XYZ dimensions and measuring systems.

The gage holes shown are the actual fixture locations that are used to build the vehicle.

Front Compartment

Front Compartment Dimensions

Location	Description	Length = x	Width = y	Height = z	Point to Point
1	Hole	1187	540	904	x
2	Hole	1299	713	9080	x
3	Strut Attachment Hole	1698	648	934	x
4	Hood Hinge Hole	1919	760	987	x
5	Hood Hinge Hole	2003	773	996	x
6	Air Inlet Grille Attachment Hole	1776	600	977	x
7	Hole	1698	648	934	x
8	Air Inlet Grille Attachment Hole	1776	600	977	x
9	Hood Hinge Hole	1919	760	987	x
10	Hood Hinge Hole	2003	773	996	x
11	Hole	1299	713	908	x
12	Hole	1187	540	904	x
13	Hood Striker Attachment Hole	1071	0	903	x
14	Impact Bar Attachment Hole	1122	540	533	x
15	Impact Bar Attachment Hole	1122	423	531	x
16	Impact Bar Attachment Hole	1122	434	320	x
17	Impact Bar Attachment Hole	1122	554	324	x
18	Impact Bar Attachment Hole	1122	423	531	x
19	Impact Bar Attachment Hole	1122	540	533	x
20	Impact Bar Attachment Hole	1122	554	324	x
21	Impact Bar Attachment Hole	1122	534	320	x
14 to 19	x	x	x	x	1080
15 to 18	x	x	x	x	846
2 to 11	x	x	x	x	1426
4 to 11	x	x	x	x	1600
2 to 9	x	x	x	x	1600
16 to 21	x	x	x	x	868
All dimensions are measured from a zero line, a center line, and a common datum. All dimensions are symmetrical unless otherwise specified.

Body Side

Body Dimensions (Long Body)

Location	Length
A-G	840 mm
A-I	1520 mm
B-F	1049 mm
B-E	1145 mm
B-C	392 mm
C-E	1059 mm
C-F	1108 mm
D-H	1956 mm
E-F	407 mm
F-H	1323 mm

Underbody

Underbody Dimensions

Location	Description	Length = x	Width = y	Height = z	Point to Point
A	Hole	1162	480	341	x
B	Hole	1261	474	287	x
C	Hole	2081	382	230	x
D	Hole	2192	600	193	x
F	Hole	3538	466	206	x
G	Hole	4955	475	404	x
H	Hole	4955	475	404	x
I	Hole	3538	466	206	x
J	Hole	2275	415	197	x
K	Hole	2192	600	193	x
L	Hole	2081	382	230	x
M	Hole	1261	474	287	x
N	Hole	1162	480	341	x
A to G	x	x	x	x	3794 mm
A to E	x	x	x	x	1124 mm
A to J	x	x	x	x	1435 mm
B to L	x	x	x	x	1187 mm
C to N	x	x	x	x	1266 mm
D to F	x	x	x	x	1353 mm
D to I	x	x	x	x	1717 mm
E to I	x	x	x	x	1540 mm
E to N	x	x	x	x	1126 mm
F to G	x	x	x	x	1431 mm
F to J	x	x	x	x	1540 mm
F to K	x	x	x	x	1717 mm
F to H	x	x	x	x	1712 mm
G to I	x	x	x	x	1712 mm
H to I	x	x	x	x	1431 mm
H to N	x	x	x	x	3794 mm
I to K	x	x	x	x	1353 mm
I to N	x	x	x	x	1124 mm

Dimensions - Body C105/Short Body

Table 1:	Front Compartment Dimensions
Table 2:	Body Dimensions (Short Body)
Table 3:	Underbody Dimensions