Engine Mechanical Specifications. Holden Barina 2008

For 1990-2009 cars only

Makes 🢒 Holden 🢒 2008 🢒 Barina 🢒 Engine 🢒 Engine Mechanical - 1.6L 🢒 Engine Mechanical Specifications

Table 1:

Application	Specification
Application	Metric	English
General Data
Engine Type	4 Cylinder - In-Line
Displacement	1598 cm³	97.51 in³
Bore Stroke	79.0x81.5 mm	3.1x3.21 in
Compression Ratio	9.5:1
Firing Order	1-3-4-2
Maximum Power - At 6200 RPM	77 kw/103.3 hp
Maximum Torque - At 3400 RPM	145 N·m	106.9 lb ft
Cylinder Bore
Diameter	79 mm	3.1102 in
Out of Round - Maximum	0.0065 mm	0.00025 in
Taper - Maximum	0.0065 mm	0.00025 in
Piston
Diameter	78.970 mm	3.1090 in
Clearance to Bore	0.020-0.040 mm	0.0008-0.0016 in
Piston Rings
Ring, End Gap - Top Compression	0.15-0.3 mm	0.006-0.012 in
Ring, End Gap - Second Compression	0.3-0.5 mm	0.012-0.019 in
Groove Clearance - Top Impression	0.05-0.08 mm	0.0019-0.0031 in
Groove Clearance - Second Compression	0.05-0.082 mm	0.002-0.003 in
Piston Pin
Diameter	18 mm	0.708 in
Pin Off-Set	0.5-0.7 mm	0.019-0.027 in
Camshaft
Lift Intake	7.2 mm	0.283 in
Lift Exhaust	7.2 mm	0.283 in
End Play	0.1-0.25 mm	0.0039-0.0079 in
Journal OD - No. 1	29.935-29.95 mm	1.1785-1.1791 in
Journal OD - No. 2	26.935-26.95 mm	1.0604-1.0610 in
Journal OD - No. 3	26.935-26.95 mm	1.0604-1.0610 in
Journal OD - No. 4	26.935-26.95 mm	1.0604-1.0610 in
Journal OD - No. 5	26.935-26.95 mm	1.0604-1.0610 in
Bearing OD - No. 1	30.01 mm	1.181 in
Bearing OD - No. 2	27.01 mm	1.063 in
Bearing OD - No. 3	27.01 mm	1.063 in
Bearing OD - No. 4	27.01 mm	1.063 in
Bearing OD - No. 5	27.01 mm	1.063 in
Crankshaft
Main Journal - Diameter - All	54.982-54.994 mm	2.164-2.165 in
Taper - Maximum	0.005 mm	0.0001 in
Out of Round - Maximum	0.004 mm	0.0001 in
Main Bearing Clearance - All	0.026-0.042 mm	0.001-0.00165 in
Crankshaft End Play	0.05-0.28 mm	0.002-0.011 in
Connecting Rod Journal - Diameter - All	43 mm	1.69 in
Taper - Maximum	0.005 mm	0.00019 in
Out of Round - Maximum	0.004 mm	0.00015 in
Rod Bearing Clearance - All	0.019-0.07 mm	0.0007-0.0027 in
Rod Side Clearance	0.07-0.242 mm	0.0027-0.009 in
Valve Stem
Valve Lash Compensators	Hydraulic
Face Angle - All	45-45, 25 degrees
Seat Angle - All	44.5-45 degrees
Seat Runout - Maximum, All	0.05 mm	0.0197 in
Face Runout - Maximum, All	0.03 mm	0.0012 in
Seat Width - Intake	1.17-1.57 mm	0.0461-0.0618 in
Seat Width - Exhaust	1.4-1.8 mm	0.055-0.071 in
Valve Guide Inside Diameter - All	6-6.02 mm	0.236-0.237 in
Valve Stem Diameter - Intake	5.955-5.97 mm	0.234-0.235 in
Valve Stem Diameter - Exhaust	5.935-5.95 mm	0.2336-0.2342 in
Valve Diameter - All - Intake	28.45-28.69 mm	1.120-1.129 in
Valve Diameter - Exhaust	27.10-27.38 mm	1.067-1.078in
Valve Spring Loads - Valve Open	554-608 N·m	408-447 lb ft
Valve Spring Loads - Valve Closed	247-273 N·m	181-200 lb ft
Lubricating Type	Forced Feed
Oil Filter Type	Cartridge (Full Flow)
Oil Pan Capacity Including Oil Filter	3.75 liter	4 quarts
Oil Pump
Gap Between Oil Pump Body and Out Rotor	0.4-0.484 mm	0.0157-0.0191 in
Out Rotor Side Clearance	0.045-0.1 mm	0.0018-0.0039 in
Inner Rotor Side Clearance	0.035-0.085 mm	0.0014-0.0033 in
Relief Valve Spring Free Length	81 mm	3.2 in
Oil Pump Type	Rotary (Trochoid)

Valve Guide Reaming Table

Size	Reamer	Production Code	Service Code
Normal	--	--	K
0.075	KM-805	1	K1
0.150	--	2	K2