Circuit Description
The body control module (BCM) controls the left front turn signal, hazard lamp, and daytime running lamp (DRL). The BCM supplies voltage to control the lighting functions. The BCM monitors the left turn signal lamp supply voltage circuit for proper operation.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC B3948 Left Front Turn Signal Circuit
Conditions for Setting the DTC
| • | B3948.02 will set if there is a short to ground in the left front turn signal circuit. |
| • | B3948.05 will set if there is an open or short to voltage in the left front turn signal circuit. |
Action Taken When the DTC Sets
| • | The Service Vehicle Soon message will be displayed. |
| • | Stores a DTC B3948 in the BCM memory |
| • | If failure is open, short to ground, or to power, rear turn signal flashes at double rate. |
Conditions for Clearing the DTC
| • | This DTC requires an ignition cycle in order to change from current to history. |
| • | The BCM no longer detects continuous battery voltage on the LH turn signal monitor circuit for longer than 5 seconds. |
| • | A history DTC will clear after 50 consecutive ignition cycles if the condition for the malfunction is no longer present. |
Diagnostic Aids
| • | The following conditions may cause an intermittent malfunction: |
| - | There is an intermittent short to voltage in the LH turn signal monitor circuit. |
| - | The turn signal switch or the hazard switch is shorted internally or is sticking. |
| • | If the BCM detects continuous voltage on the LH turn signal monitor circuit, the BCM interprets this as a short to voltage. The BCM will continue with normal DRL operation, and the LF turn signal will remain inoperative. |
| • | If the DTC is a history DTC, the problem may be intermittent. Perform the tests shown while moving related wiring and connectors. This can often cause the malfunction to occur. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems. |
Step | Action | Yes | No |
|---|---|---|---|
Schematic Reference: Exterior Lights Schematics | |||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information |
2 |
Does the left front turn signal operate properly? | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | Go to Step 3 |
3 | Observe the left front turn signal lamp. Is the lamp always ON? | Go to Step 6 | Go to Step 4 |
4 | Inspect the condition of the left front turn signal bulb. Is the bulb burned out? | Go to Step 8 | Go to Step 5 |
5 | Test for an open, high resistance, or short to ground in the left turn signal lamp supply voltage circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 10 | Go to Step 7 |
6 | Test for a short to voltage in the left turn signal lamp supply voltage circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 10 | Go to Step 7 |
7 | Inspect for poor connections at the harness connector of the body control module (BCM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 10 | Go to Step 9 |
8 | Replace the left front turn signal bulb. Refer to Headlamp Assembly or Headlamp Bulb and/or Cornering, Sidemarker, Park, Turn Signal Bulb Replacement . Did you complete the replacement? | Go to Step 10 | -- |
9 | Replace the BCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming. Did you complete the replacement? | Go to Step 10 | -- |
10 |
Does the DTC reset? | Go to Step 2 | System OK |
