Circuit Description
The body control module (BCM) applies a ground through the brake sensor reference low circuit to the brake pedal position (BPP) sensor. The BCM supplies a 5-volt reference through the brake sensor reference voltage circuit to the BPP sensor. When the brake pedal is being applied, the BPP sensor then sends a variable voltage signal through the brake sensor signal circuit to the BCM.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC C0277 Brake Pedal Position Sensor Circuit
Conditions for Running the DTC
The battery voltage must be between 9-16 volts.
Conditions for Setting the DTC
C0277 06
A short to ground or an open in the brake position sensor circuit is present.
C0277 07
A short battery positive voltage in the brake position sensor circuit or the brake position sensor low reference circuit is present.
C0277 09
A malfunctioning BPP sensor or BCM.
Action Taken When the DTC Sets
The stop lamps will not function correctly.
Conditions for Clearing the DTC
| • | The DTC will clear on current status after the condition for setting the fault is corrected. |
| • | A history DTC will clear after 100 consecutive ignition cycles without a fault present. |
| • | A history or current DTC can be cleared using a scan tool. |
Diagnostic Aids
| • | Perform a visual inspection for loose or poor connections at all related components. Refer to Testing for Intermittent Conditions and Poor Connections . |
| • | If DTC C0277 09 is set, replace the BPP sensor. If the DTC resets, replace the BCM. |
Step | Action | Yes | No |
|---|---|---|---|
Schematic Reference: Exterior Lights Schematics Connector End View Reference: Master Electrical Component List | |||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | |
2 |
Does the scan tool display a change in the voltage? | Go to Testing for Intermittent Conditions and Poor Connections | Go to Step 3 |
3 | Is DTC C0277 09 present? | Go to Step 10 | Go to Step 4 |
4 | Is DTC C0277 07 present? | Go to Step 5 | Go to Step 8 |
5 |
Does the test light illuminate? | Go to Step 6 | Go to Step 12 |
6 | Test for a short to battery positive voltage in the brake sensor signal circuit. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | Go to Step 14 | Go to Step 7 |
7 | Test for a short to battery positive voltage in the brake sensor low reference circuit. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | Go to Step 14 | Go to Step 9 |
8 | Test for a short to ground or an open on the brake sensor signal circuit. Refer to Circuit Testing and Wiring Repairs . Did you find and correct the condition? | Go to Step 14 | Go to Step 9 |
9 | Inspect for a high resistance or a poor connection at the harness connector of the brake position sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | Go to Step 14 | Go to Step 10 |
10 |
Important: Always recalibrate the brake pedal position (BPP) sensor after replacing the brake position sensor. Replace the BPP sensor. Refer to Brake Pedal Position Sensor Replacement . Did you complete the repair? | Go to Step 11 | -- |
11 |
Does DTC C0277 reset? | Go to Step 12 | Go to Step 14 |
12 | Inspect for a high resistance or a poor connection at the harness connector of the BCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs . Did you find and correct the condition? | Go to Step 14 | Go to Step 13 |
13 | Replace the BCM. Refer to Control Module References for replacement, setup, and programming. Did you complete the replacement? | Go to Step 14 | -- |
14 |
Does the DTC reset? | Go to Step 2 | System OK |
