GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The knock sensor produces an AC voltage at all engine speeds and loads. The powertrain control module (PCM) then adjusts the spark timing based on the amplitude and frequency of the KS signal. The PCM uses the KS signal to calculate the average voltage. Then the PCM assigns a voltage value. The PCM checks the knock sensor and related wiring by comparing the actual knock signal to the assigned voltage range. A normal KS signal should stay outside the assigned voltage range. This DTC will set if the KS signal is within the assigned voltage range or not present.

Conditions for Running the DTC

    • DTCs P0117, P0118, P0121, P0122, P0123, P0125, P1114, P1115, P1121, P1122 are not set.
    • Engine run time is more than 10 seconds.
    • The engine coolant temperature (ECT) is more than 60°C (131°F).
    • Engine speed is between 2000 RPM and 3000 RPM.
    • The manifold absolute pressure (MAP) is more than 45 kPa.

Conditions for Setting the DTC

The PCM detects a knock sensor voltage within the calculated average voltage range or not present.

Action Taken When the DTC Sets

    • The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.
    • The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records.

Conditions for Clearing the MIL/DTC

    • The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
    • A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
    • A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
    • Clear the MIL and the DTC with a scan tool.

Diagnostic Aids

Check the knock sensor for proper installation. A knock sensor that is loose or over torqued may cause the DTC to set.

For an intermittent condition, refer to Intermittent Conditions .

Check and correct any abnormal engine noise before using the diagnostic table.

Step

Action

Values

Yes

No

Schematic Reference:

Ignition Controls


Object Number: 789678  Size: FS
Master Electrical Component List
Electronic Ignition (EI) System Description
Fuel Pump Controls
Power, Ground, MIL and DLC
OBD II Symbol Description Notice
Ignition A, Ignition B Fuses, and Ignition Switch
ECM 1 and Ignition E Fuses (5.0L and 5.7L)
G103 (4.3L, 5.0L, and 5.7L Engines)

1

Did you perform the Diagnostic System Check-Engine Controls?

--

Go to Step 2

Go to

Diagnostic System Check - Engine Controls

2

Important: If an engine knock can be heard, repair the engine mechanical condition before proceeding with this diagnostic.

  1. Observe the Freeze Frame/Failure Records data for this DTC.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the engine within the Conditions for Running the DTC or as close to the Freeze Frame/Failure Records data that you observed.

Does the scan tool indicate that this diagnostic failed this ignition?

--

Go to Step 3

Go to Diagnostic Aids

3

  1. Disconnect the knock sensor harness.
  2. Set the DMM to the 400K ohm scale.
  3. Measure the resistance of the knock sensor using the DMM connected to a good ground.

Is the resistance of the knock sensor near the specified range?

100 K

Go to Step 4

Go to Step 6

4

  1. With the DMM still connected, set the DMM to the 400 mV AC Hertz scale. Refer to Measuring Frequiency in Wiring Systems.
  2. Important: Do not tap on plastic engine components.

  3. Tap on the engine block near the appropriate knock sensor while observing the signal indicated on the DMM.

Is any signal indicated on the DMM while tapping on the engine block near the knock sensor?

--

Go to Step 5

Go to Step 6

5

  1. Disconnect the PCM connector. Refer to Powertrain Control Module Replacement .
  2. Test the KS signal circuit between the PCM and the knock sensor connector for the following:
  3. • An open
    • A short to voltage
    • A short to ground

Refer to Testing for Continuity , Testing for a Short to Voltage , and Testing for Short to Ground in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 9

Go to Step 7

6

Replace the knock sensor. Refer to Knock Sensor Replacement .

Did you complete the replacement?

--

Go to Step 9

--

7

  1. Inspect the KS signal circuit for a poor connection at the PCM or the knock sensor harness connector. Refer to Intermittent and Poor Connections in Wiring Systems.
  2. If you find a poor connection, repair the connector as necessary. Refer to Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 9

Go to Step 8

8

Replace the PCM. Refer to Powertrain Control Module Replacement .

Did you complete the replacement?

--

Go to Step 9

--

9

  1. Select the diagnostic trouble code (DTC) option and the Clear DTC Information option using the scan tool.
  2. Idle the engine at the normal operating temperature.
  3. Select the diagnostic trouble code (DTC) option and the Specific DTC option, then enter the DTC number using the scan tool.
  4. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.

Does the scan tool indicate that this test ran and passed?

--

Go to Step 10

Go to Step 2

10

Select the Capture Info option and Review Info option using the scan tool.

Does the scan tool display any DTCs that you have not diagnosed?

--

Go to Diagnostic Trouble Code (DTC) List

System OK