Circuit Description
The powertrain control module (PCM) supplies a bias voltage of about 450 mV between the HO2S and low signal circuits. When measured with a 10 megohm digital voltmeter, this may display as low as 320 mV. The oxygen sensor varies the voltage within a range of about 1000 mV when the exhaust is rich, down through about 10 mV when exhaust is lean. The PCM constantly monitors the HO2S signal during closed loop operation and compensates for a rich or lean condition by decreasing or increasing injector pulse width as necessary. If the HO2S 1 voltage remains at or near the 450 mV bias for an extended period of time, DTC P0134 will be set, indicating an open HO2S high signal or HO2S low signal circuit.
Conditions for Running the DTC
| • | No TP sensor, EVAP system, misfire, IAT sensor, MAP sensor, fuel trim, fuel injector circuit, EGR Pintle Position, ECT sensor, CKP Sensor, or MAF sensor DTC present. |
| • | Engine run time longer than 200 seconds. |
Conditions for Setting the DTC
HO2S 1 signal voltage remains between 400 mV and 500 mV for longer than 30 seconds.
Action Taken When the DTC Sets
| • | The PCM will illuminate the malfunction indicator lamp (MIL) during the second consecutive trip in which the diagnostic test has been run and failed. |
| • | The PCM will store conditions which were present when the DTC set as Freeze Frame/Failure Records data. |
Conditions for Clearing the MIL/DTC
| • | The PCM will turn OFF the malfunction indicator lamp (MIL) during the third consecutive trip in which the diagnostic has run and passed. |
| • | The history DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction. |
| • | The DTC can be cleared by using a scan tool. |
Diagnostic Aids
Check for the following conditions:
| • | Poor connection or damaged harness |
| Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, poor terminal to wire connection, and damaged harness. |
| • | Malfunctioning HO2S heater or heater circuit |
| With the ignition ON, engine not running, the HO2S voltage displayed on a scan tool should drop to less than 250 mV or rise to above 600 mV within 2 minutes. If not, disconnect the HO2S and connect a test light between the HO2S ignition feed and heater ground circuits. If the test light does not light, repair the open ignition feed or the HO2S heater ground circuit as necessary. Refer to Wiring Repairs in Wiring Systems. If the test light lights and the HO2S signal and low circuits are OK, replace the HO2S. |
| • | Intermittent test |
| With the ignition ON, monitor the HO2S signal voltage while moving the wiring harness and related connectors. If the malfunction is induced, the HO2S signal voltage will change. This may help isolate the location of the malfunction. |
Review the Fail Records vehicle mileage since the diagnostic test last failed to help determine how often the condition that caused the DTC to be set occurs. This may assist in diagnosing the condition.
Test Description
Number(s) below refer to the step number(s) on the Diagnostic Table.
Step | Action | Value(s) | Yes | No | ||||
|---|---|---|---|---|---|---|---|---|
1 | Was the Powertrain On-Board Diagnostic (OBD) System Check performed? | -- | ||||||
2 |
Does the scan tool indicate HO2S 1 voltage varying outside the specified values? | 400-500 mV | ||||||
3 |
Does the scan tool indicate DTC failed this ignition? | -- | Go to Diagnostic Aids | |||||
4 |
Is HO2S 1 voltage less than the specified value? | 150 mV | ||||||
5 |
Does HO2S 1 signal voltage measure near the specified value? | 4.5 V | ||||||
6 |
Was a problem found? | -- | ||||||
7 |
Was a problem found? | -- | ||||||
8 |
Was a problem found? | -- | ||||||
9 |
Was a problem found? | -- | ||||||
10 |
Was a problem found? | -- | ||||||
11 | Replace HO2S 1. Refer to Heated Oxygen Sensor Replacement - Sensor 1 . Is the action complete? | -- | -- | |||||
|
Important:: The replacement PCM must be programmed. Replace the PCM. Refer to Powertrain Control Module Replacement/Programming . | -- | -- | ||||||
13 |
Does the scan tool indicate DTC failed this ignition? | -- | System OK |
