Refer to
Ignition Control Module
.
Circuit Description
The 18X reference signal is produced by the ignition control module. The ICM calculates the 18X reference signal by filtering the crankshaft position (CKP) sensor 18X pulses when the engine is running and CKP sync pulses are also being received. The PCM uses the 18X reference signal to calculate engine RPM and crankshaft position at engine speeds below 1200 RPM. The PCM constantly monitors the number of pulses on the 18X reference circuit and compares the number of 18X reference pulses to the number of 3 X reference pulses and CAM signal pulses being received. If the PCM receives an incorrect number of pulses on the 18X reference circuit, DTC P0336 will set and the PCM will use the 3X reference signal circuit for fuel and ignition control. The engine will continue to start and run using the 3X reference and CAM signals only.
Conditions for Setting the DTC
| • | The engine is running (3X reference pulses are being received). |
| • | The ratio of 18X reference pulses to 3X reference pulses received by the PCM does not equal 6 to 1. |
| • | The ratio of 3X reference pulses to CAM signal pulses received by the PCM equals 6 to 1. |
| • | Above conditions for 80 occurrences. |
Action Taken When the DTC Sets
| • | The PCM will illuminate the malfunction indicator lamp (MIL) during the second consecutive trip in which the diagnostic test has been run and failed. |
| • | The PCM will store conditions which were present when the DTC set as Freeze Frame and Failure Records data. |
Action Taken When the DTC Sets
| • | The PCM will illuminate the MIL during the second consecutive trip in which the diagnostic test has been run and failed. |
| • | The PCM will use the 3X reference signal circuit for fuel and ignition control. |
| • | If equipped with traction control, the PCM will command the EBTCM via serial data (CKT 800) to set an ABS/TCS DTC, the EBTCM will turn OFF traction control, and the EBTCM will illuminate the TRACTION OFF lamp. |
| • | The PCM will store conditions which were present when the DTC set as Freeze Frame and Fail Records data. |
Diagnostic Aids
An intermittent may be caused by a poor connection, rubbed through wire insulation or a wire broken inside the insulation. Check for the following conditions:
| • | Poor connection. Inspect the PCM harness and connectors for improper mating, broken locks, improperly formed or damaged terminals, and poor terminal to wire connection. |
| • | Damaged harness. Inspect the wiring harness for damage. If the harness appears to be OK, disconnect the PCM, turn the ignition on and observe a voltmeter connected to the 18X reference circuit at the PCM harness connector while moving connectors and wiring harnesses related to the ICM. A change in voltage will indicate the location of the malfunction. |
| • | Incorrect harness routing near secondary ignition components. |
| • | Malfunctioning Ignition Coil. Remove the ignition coils and inspect the ignition control module and coils for cracks, carbon tracking, or other signs that indicate that the coil secondary circuit is arcing to the ICM or ICM wiring harness. Refer to Ignition Control Module Replacement . |
| • | Secondary ignition wire(s) arcing to wiring harness. Check secondary ignition wires for carbon tracking or other signs of damage. |
Reviewing the Fail Records vehicle mileage since the diagnostic test last failed may help determine how often the condition that caused the DTC to be set occurs. This may assist in diagnosing the condition.
Test Description
Number(s) below refer to the step number(s) on the Diagnostic Table.
Step | Action | Value(s) | Yes | No | ||||||
|---|---|---|---|---|---|---|---|---|---|---|
1 | Was the Powertrain On-Board Diagnostic (OBD) System Check performed? | -- | ||||||||
2 | Attempt to start the engine. Does the engine start? | -- | ||||||||
3 |
Is DTC P0336 set? | -- | Refer to Diagnostic Aids | |||||||
4 |
Was a problem found? | -- | ||||||||
5 |
Is voltage near the specified value? | 3V | ||||||||
6 |
Was a problem found? | -- | ||||||||
7 | Replace the ignition control module. Refer to Ignition Control Module Replacement . Is action complete? | -- | -- | |||||||
8 |
Was a problem found? | -- | ||||||||
9 | Check connections at the PCM and replace terminals if necessary. Refer to Repair Procedures in Electrical Diagnosis. Did any terminals require replacement? | -- | ||||||||
Replace the PCM. Important:: The replacement PCM must be programmed. Refer to Powertrain Control Module Replacement/Programming . Is action complete? | -- | -- | ||||||||
11 |
Note test result; does scan tool indicate DTC P0336 failed this ign? | -- | System OK |
