GM Service Manual Online
For 1990-2009 cars only

Important: The DTC descriptor that the scan tool displays will not match this DTC due to DTCs P0567 and P0568 being reversed within the engine control module (ECM). This will only affect this vehicle for the 2004 model year.

Circuit Description

The cruise control resume/accel switch is an input to the ECM. The ECM uses the cruise control resume/accel switch signal circuit in order to detect when the driver has requested to accelerate the set vehicle speed or to resume the Cruise Control System. The ECM detects a voltage signal on the cruise control resume/accel switch signal circuit when the switch is applied.

Conditions for Running the DTC

The Ignition is ON.

The cruise control On/Off switch is ON.

Conditions for Setting the DTC

    • The ECM detects a voltage signal on the cruise control resume/accel switch signal circuit for longer than 60 seconds.
    • This ECM runs this diagnostic every 0.05 seconds.

Action Taken When the DTC Sets

    • The ECM stores the DTC information into memory when the diagnostic runs and fails.
    • The malfunction indicator lamp (MIL) will not illuminate.
    • The ECM records the operating conditions at the time the diagnostic fails. The ECM stores this information in the Failure Records.
    • The Cruise Control System is disabled.

Conditions for Clearing the MIL/DTC

    • A last test failed, or the current DTC, clears when the diagnostic runs and does not fail.
    • A history DTC clears after 40 consecutive warm-up cycles, if failures are not reported by this or any other emission related diagnostic.
    • Use a scan tool in order to clear the MIL/DTC.

Diagnostic Aids

    • Ensure that the resume/accel switch is not stuck or sticking in the engaged position.
    • For an intermittent condition, refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. This step determines if condition is present.

  2. This step determines if the switch is at fault.

Step

Action

Yes

No

Schematic Reference: Cruise Control Schematics

Connector End View Reference: Cruise Control Connector End Views or to Engine Control Module Connector End Views in Engine Controls - 3.6L (LY7)

1

Did you perform the Cruise Control Diagnostic System Check?

Go to Step 2

Go to Diagnostic System Check - Cruise Control

2

  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. Turn the cruise control On/Off switch ON.
  4. With the scan tool, observe the Cruise Resume/Accel. Switch parameter in the Powertrain 3.6L Cruise/Traction data list.

Does the Cruise Resume/Accel. Switch parameter display On?

Go to Step 3

Go to Diagnostic Aids

3

  1. Turn OFF the ignition.
  2. Disconnect C4 of the multifunction switch.
  3. Turn ON the ignition, with the engine OFF.
  4. With the scan tool, observe the Cruise Resume/Accel. Switch parameter.

Does the Cruise Resume/Accel. Switch parameter display On?

Go to Step 4

Go to Step 5

4

Test the cruise control resume/accel switch signal circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 9

Go to Step 6

5

Inspect for poor connections at the harness connector of the multifunction switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 9

Go to Step  7

6

Inspect for poor connections at the harness connector of the engine control module (ECM). Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 9

Go to Step 8

7

Replace the multifunction switch. Refer to Turn Signal Multifunction Switch Replacement in Steering Wheel and Column.

Did you complete the replacement?

Go to Step 9

--

8

Important: Program the replacement ECM.

Replace the ECM. Refer to Engine Control Module Replacement in Engine Controls - 3.6L (LY7).

Did you complete the replacement?

Go to Step 9

--

9

  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC.

Does the DTC reset?

Go to Step 2

System OK