GM Service Manual Online
For 1990-2009 cars only

Step

Action

Values

Yes

No

Schematic Reference: HVAC Schematics

Connector End View Reference: HVAC Connector End Views

DEFINITION: The A/C compressor clutch will not disengage when an A/C request has not been made and a Powertrain DTC has not been set.

1

Did you perform the HVAC Diagnostic System Check?

--

Go to Step 2

Go to Scan Tool Output Controls

2

  1. Start the engine.
  2. Place the blower motor switch in the OFF position.
  3. Place the A/C request switch in the OFF position.

Does the A/C compressor operate?

--

Go to Step 3

Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

3

With a scan tool, observe the A/C request signal parameter in the Powertrain data list.

Does the scan tool indicate that the A/C request signal parameter is YES?

--

Go to Step 4

Go to Step 6

4

Test the A/C request signal circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 18

Go to Step 5

5

  1. Turn OFF the ignition.
  2. Disconnect the A/C high pressure switch.
  3. Start the engine.
  4. With a scan tool, observe the A/C request signal parameter.

Does the scan tool indicate that the A/C request signal parameter is YES?

--

Go to Step 13

Go to Step 12

6

With a scan tool, command the A/C compressor clutch relay ON and OFF.

Does the A/C compressor clutch relay turn ON and OFF with each command?

--

Go to Step 7

Go to Step 9

7

Remove the A/C compressor clutch relay.

Is the A/C compressor ON?

--

Go to Step 10

Go to Step 8

8

Measure the resistance between the switch side A/C compressor clutch relay terminals.

Does the resistance measurement equal the specified value?

Go to Step 9

Go to Step 11

9

Test the A/C clutch relay control circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 18

Go to Step 13

10

Test the A/C compressor clutch supply voltage circuit for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 18

Go to Step 15

11

Inspect for poor connections at the A/C compressor clutch relay. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 18

Go to Step 14

12

Inspect for poor connections at the harness connector of the HVAC control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 18

Go to Step 16

13

Inspect for poor connections at the harness connector of the powertrain control module (PCM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 18

Go to Step 17

14

Replace the A/C compressor clutch relay.

Did you complete the replacement?

--

Go to Step 18

--

15

Replace the A/C compressor clutch. Refer to Air Conditioning Compressor Replacement in Heating, Ventilation, and Air Conditioning.

Did you complete the replacement?

--

Go to Step 18

--

16

Replace the HVAC control module. Refer to HVAC Control Module Replacement .

Did you complete the replacement?

--

Go to Step 18

--

17

Important:: Perform the reprogramming procedure for the PCM.

Replace the PCM. Refer to Powertrain Control Module Replacement in Engine Controls - 3.4L.

Did you complete the replacement?

--

Go to Step 18

--

18

Operate the system in order to verify the repair.

Did you correct the condition?

--

System OK

Go to Step 3