GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The seat adjuster motors are equipped with potentiometer type position sensors used by the memory seat module to determine the seat position. The motor position sensors are supplied with 5-volt reference and ground circuits from the memory seat module. The position sensor signal circuits are referenced from ground within the memory seat module. The signal voltages monitored by the memory seat module range from 0.24-4.75 volts and are determined by the wiper locations on the resistors within the position sensors. The position sensor circuit voltage levels are used by the memory seat module to determine the position of the seat when storing or recalling memory position settings.

Conditions for Running the DTC

The system voltage must be between 9.0 and 16.0 volts.

Conditions for Setting the DTC

The memory seat module detects the position sensor signal circuit under 0.24 volts or over 4.75 volts.

Action Taken When the DTC Sets

Memory functions will be disabled as long as the fault is current.

Conditions for Clearing the DTC

    • The DTC will be current for as long as the fault is present.
    • When the fault is no longer present the DTC will be a history status code.
    • The history DTC will be cleared after 100 error free ignition cycles, or by using the scan tool clearing DTCs feature.

Step

Action

Values

Yes

No

Schematic Reference: Memory Seats Schematics

Connector End View Reference: Power Seat Connector End Views

1

Did you perform the Power Seat Systems Diagnostic System Check?

--

Go to Step 2

Go to Diagnostic System Check - Power Seat Systems

2

  1. Install a scan tool.
  2. With the scan tool, observe the position sensor parameter in the memory seat module data list.

Does the scan tool indicate that the position sensor parameter is within the specified range?

0.2-4.7 V

Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

Go to Step 3

3

  1. Disconnect the position sensor connector.
  2. Measure the voltage between the 5-volt reference circuit of the position sensor and a good ground.

Does the voltage measure within the specified range?

4.7-5 V

Go to Step 5

Go to Step 4

4

Test the 5-volt reference circuit of the position sensor for the following conditions:

    • Open or high resistance
    • Short to ground
    • Short to voltage

Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 12

Go to Step 9

5

  1. Connect a 3-amp fused jumper wire between the 5-volt reference circuit of the position sensor and the signal circuit of the position sensor.
  2. With a scan tool, observe the position sensor parameter.

Does the scan tool indicate that the position parameter is within the specified range?

4.7-5 V

Go to Step 7

Go to Step 6

6

Test the signal circuit of the position sensor for the following conditions:

    • Open or high resistance
    • Short to ground
    • Short to voltage

Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 12

Go to Step 9

7

Test the low reference circuit of the position sensor for an open or high resistance. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 12

Go to Step 8

8

Inspect for poor connections at the harness connector of the position sensor. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 12

Go to Step 10

9

Inspect for poor connections at the harness connector of the memory seat module. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 12

Go to Step 11

10

Replace the seat position sensor. Refer to Front Seat Adjuster Replacement .

Did you complete the replacement?

--

Go to Step 12

--

11

Replace the memory seat module. Refer to Memory Seat Control Module Replacement .

Did you complete the replacement?

--

Go to Step 12

--

12

  1. Use the scan tool in order to clear the DTCs.
  2. Operate the system within the Conditions for Running the DTC as specified in the supporting text.

Does the DTC reset?

--

Go to Step 2

System OK